List of Academic Papers by Masahito MOCHIZUKI
(Updated on 1st July, 2012)

1. Original Papers through Peer Review

(142) T. Hashimoto, Y. Osawa, S. Itoh, M. Mochizuki and K. Nishimoto, Long-Term Stability of Residual Stress Improvement by Water Jet Peening Considering Working Processes, Transactions of the ASME, Journal of Pressure Vessel Technology, American Society of Mechanical Engineers, Vol. 134, in press (2012).　

(141) T. Sera, S. Hirano, N. Chigusa, S. Okano, K. Saida, M. Mochizuki and K. Nishimoto, Prediction Method of Long-Term Reliability in Improving Residual Stresses by Means of Surface Finishing, Journal of Japan Society of Maintenology (in Japanese), Vol. 11, No. 3, in press (2012).　

(140) M. Iyota, Y. Mikami, T. Hashimoto, K. Taniguchi, R. Ikeda and M. Mochizuki, The Effect of Martensitic Transformation on Residual Stress in Resistance Spot Welded High-Strength Steel Sheets, Journal of Alloys and Compounds, in press (2012).　

(139) T. Hashimoto, T. Shobu and M. Mochizuki, Consideration of Microstructure Evolution and Residual Stress Measurement near Severe Worked Surface Using High Energy X-ray, Journal of the Society of Materials Science, Japan (in Japanese), Vol. 61, No. 7, in press (2012).　

(138) H. Kitano, S. Okano and M. Mochizuki, A Study for High Accuracy Measurement of Residual Stress by Deep Hole Drilling Technique, Journal of Physics, Conference Series, in press (2012).　

(137) M. Hata, S. Itoh, T. Sugihiro, Y. Yamashita, A. Kamio, M. Shibahara, and M. Mochizuki, Investigation of Factors Influencing Welding Deformation of Ship Block by Inherent Strain Analysis Using Idealized Explicit FEM, Journal of Physics, Conference Series, in press (2012).　

(136) A. Sugahara, S. Okano, T. Hashimoto and M. Mochizuki, Comparison of Weld Residual Stress Measurement Results in Low Alloy Welds Between X-Ray Diffraction and Stress Relief Methods, Journal of Physics, Conference Series, in press (2012).　

(135) N. Kubota, Y. Mikami, M. Mochizuki and K. Hiraoka, Numerical Simulation of the Effect of Low-Temperature Transformation Expansion on Residual Stress in Cold Cracking Test Specimens of Different Restraint Factors, Journal of Physics, Conference Series, in press (2012).　

(134) R. Ihara, T. Hashimoto and M. Mochizuki, Residual Stress Variation due to Piping Processes of Austenitic Stainless Steel, Journal of Physics, Conference Series, in press (2012).　

(133) T. Sakai, Y. Mikami and M. Mochizuki, Effect of Columnar Grain Shape Modeling on the Microscopic Stress Distribution at the Clad Weld Metal Surface of Ni Base Alloy, Journal of Physics, Conference Series, in press (2012).　

(132) M. Iyota, Y. Mikami, T. Hashimoto, K. Taniguchi, R. Ikeda and M. Mochizuki, Effect of Electrode Force Condition on Nugget Diameter and Residual Stress in Resistance Spot Welded High-Strength Steel Sheets, Journal of Physics, Conference Series, in press (2012).　

(131) S. Okano, M. Mochizuki, M. Toyoda and T. Ueyama, Effect of Welding Conditions on Reduction of Angular Distortion by Welding with Trailing Heat Sink, Science and Technology of Welding and Joining, Vol. 17, No. 4, pp. 264-268 (2012).　

(130) A. Kawaguchi, S. Itoh, M. Mochizuki and M. Kameyama, Large-Scale Computation of Welding Residual Stress, Progress in Nuclear Science and Technology, Vol. 2, pp. 613-619 (2011).　

(129) K. Torigata, S. Okano and M. Mochizuki, Fundamental Study on Balance between Strength and Deformation in Undermatched High-Tensile Strength Steel Weld Joint of Beam-to-Column Connections, Journal of Construction Steel (in Japanese), Vol. 19, pp. 179-186 (2011).　

(128) L. Yu, Y. Nakabayashi, M. Sasa, S. Itoh, M. Kameyama, S. Hirano, N. Chigusa, K. Saida, M. Mochizuki and K. Nishimoto, Neural Network Prediction of Hardness in HAZ of Temper Bead Welding Using the Proposed Thermal Cycle Tempering Parameter (TCTP), ISIJ International, Vol. 51, No. 9, pp. 1516-1515 (2011).　

(127) L. Yu, Y. Nakabayashi, M. Sasa, S. Itoh, K. Saida, M. Mochizuki, K. Nishimoto, M. Kameyama, S. Hirano and N. Chigusa, Prediction of Hardness in HAZ of Multi-Pass Welds in Low-Alloy Steel Using Neural Network, Quarterly Journal of the Japan Welding Society (in Japanese), Vol. 29, No. 3, pp. 154-161 (2011).　

(126) Y. Mikami, K. Sogabe and M. Mochizuki, EBSP-based Crystal Plasticity FEM Simulation of Microscopic Stress Distribution in Weld Metal, Quarterly Journal of Japan Welding Society, Vol. 29, No. 3, pp. 100s-103s (2011).　

(125) T. Hashimoto, S. Okano and M. Mochizuki, Welding-Metallurgical Evaluation for Residual Stress Measurement Accuracy of Multi-Pass Girth Welded Pipe Joint in Austenitic Stainless Steel by X-Ray Diffraction, Journal of the Society of Materials Science, Japan (in Japanese), Vol. 60, No. 7, pp. 610-616 (2011).　

(124) T. Hashimoto, Y. Osawa, S. Hirano, M. Mochizuki and K. Nishimoto, Accuracy Improvement of X-Ray Stress Measurement on GTA Weld of Type 600 Ni Based Alloy, Journal of the Society of Materials Science, Japan (in Japanese), Vol. 60, No. 7, pp. 604-609 (2011).　

(123) L. Yu, Y. Nakabayashi, K. Saida, M. Mochizuki, K. Nishimoto, M. Kameyama, S. Hirano and N. Chigusa, Quantitative Consideration for the Tempering Effect during Multi-pass Thermal Cycle in HAZ of Low-Alloy Steel, Quarterly Journal of the Japan Welding Society (in Japanese), Vol. 29, No. 2, pp. 107-113 (2011).　

(122) S. Okano, M. Mochizuki, K. Yamamoto and M. Tanaka, An Attempt to Enhance Numerical Models of Angular Distortion by Considering the Physics of the Welding Arc, Welding in the World, Vol. 55, No. 5/6, pp. 93-100 (2011).　

(121) R. Ihara, J. Katsuyama, K. Onizawa, T. Hashimoto, Y. Mikami and M. Mochizuki, Prediction of Residual Stress Distributions due to Surface Machining and Welding and Crack Growth Simulation under Residual Stress Distribution, Nuclear Engineering and Design, Vol. 241, pp. 1335-1344 (2011).　

(120) M. Iyota, Y. Mikami, T. Hashimoto, K. Taniguchi, R. Ikeda and M. Mochizuki, Numerical Simulation of Nugget Size and Residual Stress of Resistance Spot Welded HT980 Steel Sheet, Quarterly Journal of the Japan Welding Society (in Japanese), Vol. 29, No. 2, pp. 86-95 (2011).　

(119) S. Okano, M. Tanaka and M. Mochizuki, Numerical Analysis of Weld Distortion using Arc Physics Based Heat Source Modeling - A Discussion about Relationship between Heat Input Parameter and Angular Distortion, Quarterly Journal of the Japan Welding Society (in Japanese), Vol. 29, No. 2, pp. 77-85 (2011).　

(118) S. Okano, M. Mochizuki, M. Toyoda and T. Ueyama, Effect of Weld Shrinkage on Root Gap Behavior during Butt Welding with Additional Cooling behind Weld Heat Source, Quarterly Journal of the Japan Welding Society (in Japanese), Vol. 29, No. 2, pp. 70-76 (2011).　

(117) M. Mochizuki and M. Toyoda, Prediction of Ductile-to-Brittle Transition Under Different Strain Rates in Undermatched Welded Joints, Transactions of the ASME, Journal of Pressure Vessel Technology, American Society of Mechanical Engineers, Vol. 133, No. 3, 031401-1-8 (2011).　

(116) S. Hirano, T. Sera, N. Chigusa, L. Yu, M. Mochizuki and K. Nishimoto, Study on Implementing Newly Developed Repair Welding Technique within a Limited Time Frame for Nuclear Power Plant, Journal of Japan Society of Maintenology (in Japanese), Vol. 10, No. 1, pp. 35-43 (2011).　

(115) T. Hashimoto, Y. Osawa, S. Hirano, M. Mochizuki and K. Nishimoto, Accuracy Improvement of X-Ray Residual Stress Measurement in Welds of Ni Based Alloy by Two-Dimensional Detector with Multiaxial Rocking, Science and Technology of Welding and Joining, Vol. 16, No. 3, pp. 261-266 (2011).　

(114) S. Okano, M. Tanaka and M. Mochizuki, Arc Physics Based Heat Source Modeling for Numerical Simulation of Weld Residual Stress and Distortion, Science and Technology of Welding and Joining, Vol. 16, No. 3, pp. 209-214 (2011).　　

(113) S. Okano, M. Mochizuki, M. Toyoda and T. Ueyama, Effect of Weld Heat Input Conditions on Reduction of Angular Distortion by Heat-Sink Welding, Quarterly Journal of the Japan Welding Society (in Japanese), Vol. 29, No. 1, pp. 55-60 (2011).　

(112) K. Miyazaki and M. Mochizuki, The Effects of Residual Stress Distribution and Component Geometry on the Stress Intensity Factor of Surface Cracks, Transactions of the ASME, Journal of Pressure Vessel Technology, American Society of Mechanical Engineers, Vol. 133, No. 1, 011701-1-7 (2011).　

(111) H. Kitano, S. Okano and M. Mochizuki, Fundamental Study on Design of Welded Joints with Soft Weld Metal for Expanding Coverage of High-Tensile Steel, Journal of Construction Steel (in Japanese), Vol. 18, pp. 165-172 (2010).　

(110) Y. Mikami, R. Uraguchi, K. Sogabe and M. Mochizuki, SCC Prediction in Weld Components by Multi-Scale Analysis Incorporating Crystal Plasticity, Mathematical Modelling of Weld Phenomena 9, Edited by H. Cerjak, TU Graz Publishing, Graz, Austria, pp. 699-713 (2010).　

(109) M. Mochizuki, M. Tanaka and S. Okano, Distortion Analysis by Combining Arc Plasma Process with Weld Mechanics, Mathematical Modelling of Weld Phenomena 9, Edited by H. Cerjak, TU Graz Publishing, Graz, Austria, pp. 551-578 (2010).　

(108) T. Kawabata, H. Sakaibori, K. Onishi, H. Kitano, S. Okano and M. Mochizuki, Effect of Undermatched Joint on Brittle Fracture Behavior of High Strength Steel Plate - Mechanical Discussion on 950MPa Class Steel Plate Welded Joint for Penstock, Quarterly Journal of the Japan Welding Society (in Japanese), Vol. 28, No. 3, pp. 296-304 (2010).　

(107) H. Kitano, S. Okano, M. Mochizuki, K. Onishi, T. Kawabata and H. Sakaibori, Evaluation of the Effect of Strength Mismatch in Undermatched Joints on the Static Tensile Strength of Welded Joints by Considering Microstructure - Mechanical Discussion on 950MPa Class Steel Plate Welded Joint, Quarterly Journal of the Japan Welding Society (in Japanese), Vol. 28, No. 3, pp. 288-295 (2010).　

(106) S. Okano, K. Matsushita, M. Mochizuki and M. Toyoda, A Discussion about Relationship between Heat Input Parameter and Angular Distortion by Considering Moving Heat Source Effect, Quarterly Journal of the Japan Welding Society (in Japanese), Vol. 28, No. 3, pp. 272-280 (2010).　

(105) H. Shirai, M. Mochizuki and M. Toyoda, Development of Joining Process between Aluminum Alloy and Stainless Steel by Using Plastic Flow in Automotive Parts, Journal of Light Metal Welding and Construction (in Japanese), Vol. 48, No. 8, pp. 286-292 (2010).　

(104) N. Ochi, S. Okano, M. Mochizuki, J. Shimamura and N. Ishikawa, Thermal Conduction Theoretical Analysis of Temperature Distribution during Multiple-Electrode Submerged Arc Welding, Quarterly Journal of the Japan Welding Society (in Japanese), Vol. 28, No. 1, pp. 158-166 (2010).　

(103) S. Okano and M. Mochizuki, A Methodology of Appropriate Weld Procedures for Axial Compressive Residual Stress on Inner Surface in Multi-Pass Girth Welded Pipe Joint, Journal of the Japan High Pressure Institute (in Japanese), Vol. 48, No. 2, pp. 86-96 (2010).　

(102) J. Yamamoto, K. Hiraoka and M. Mochizuki, Analysis of Martensite Transformation Behavior in Welded Joint of Low Transformation-Temperature Welding Wire, Science and Technology of Welding and Joining, Vol. 15, No. 2, pp. 104-110 (2010).　

(101) M. Shibahara, E. Kawamura, K. Ikushima, S. Itoh, M. Mochizuki and K. Masaoka, Development of Three-Dimensional Welding Deformation Measurement Based on Stereo Imaging Technique, Quarterly Journal of the Japan Welding Society (in Japanese), Vol. 28, No. 1, pp. 108-115 (2010).　

(100) S. Okano, K. Matsushita, M. Mochizuki, M. Toyoda and T. Ueyama, Experimental Study on Relationship between Heat Input Parameter and Angular Distortion, Quarterly Journal of the Japan Welding Society (in Japanese), Vol. 28, No. 1, pp. 97-107 (2010).　

(99) S. Okano, M. Mochizuki and M. Toyoda, Weld Residual Distortion Produced due to Locally Cooled Temperature Distribution and Its Reduction Effect, Quarterly Journal of the Japan Welding Society (in Japanese), Vol. 28, No. 1, pp. 72-79 (2010).　

(98) R. Higuchi, M. Mochizuki and M. Toyoda, FEM-MD Combined Method for Evaluation of Microscopic Stress Distribution by Considering Microscopic Heterogeneity and Deformation in Close Vicinity to Grain Boundary of Steels, Quarterly Journal of the Japan Welding Society (in Japanese), Vol. 28, No. 1, pp. 28-38 (2010).　

(97) Y. Mikami, M. Mochizuki and M. Toyoda, Effect of Transformation Temperature and Restraint Intensity on the Reduction of Restraint Stress by Transformation Expansion, Quarterly Journal of Japan Welding Society, Vol. 27, No. 2, pp. 235s-239s (2009).　

(96) S. Okano, M. Mochizuki and M. Toyoda, Effect of Welding Conditions on Reduction of Angular Distortion by In-Process Control Welding Using Back Heating Source, Quarterly Journal of Japan Welding Society, Vol. 27, No. 2, pp. 231s-234s (2009).　

(95) Y. Mikami, A. Inao, M. Mochizuki and M. Toyoda, Numerical Simulation of Transformation-Induced Microscopic Residual Stress in Ferrite-Martensite Lamellar Steel, Journal of Physics, Conference Series, Vol. 165, No. 012080, pp. 1-4, IOP Publishing Limited (2009).　

(94) M. Mochizuki, Y. Mikami, S. Okano and S. Itoh, Computational Simulation of Weld Microstructure and Distortion by Considering Process Mechanics, Journal of Physics, Conference Series, Vol. 165, No. 012014, pp. 1-6, IOP Publishing Limited (2009).　

(93) R. Higuchi, M. Mochizuki and M. Toyoda, Evaluation Method for Stress-Strain Relationship of Materials in Microstructural Region Using Triangular Pyramidal Indenter, Quarterly Journal of the Japan Welding Society (in Japanese), Vol. 27, No. 2, pp. 115-123 (2009).

(92) M. Mochizuki, G. B. An and M. Toyoda, Thermal Elastic-Plastic Analysis Considering Temperature Rise by Rapid Plastic Deformation in Undermatched Joints, Transactions of the ASME, Journal of Pressure Vessel Technology, American Society of Mechanical Engineers, Vol. 131, No. 3, DOI: 10.1115/1.3027477, 031202-1-11 (2009).

(91) K. Miyazaki, M. Numata, K. Saito and M. Mochizuki, Effect of Distance from the Center of Weld to the Fixed End on Residual Stress and Stress Intensity Factor of the Piping Weld, Transactions of the ASME, Journal of Pressure Vessel Technology, American Society of Mechanical Engineers, Vol. 131, No. 2, DOI: 10.1115/1.3007428, 021205-1-9 (2009).

(90) Y. Mikami, Y. Morikage, M. Mochizuki and M. Toyoda, Angular Distortion of Fillet Welded T Joint Using Low Transformation Temperature Welding Wire, Science and Technology of Welding and Joining, Vol. 14, Vol. 2, pp. 97-105 (2009).

(89) M. Mochizuki, Y. Mikami, H. Yamasaki and M. Toyoda, Analytical Study on Effects of Strain Distribution in Welding Start/End on Welding Distortion, Quarterly Journal of the Japan Welding Society (in Japanese), Vol. 26, No. 2, pp. 145-151 (2008).

(88) H. Shirai, S. Okano, M. Mochizuki and M. Toyoda, Study of Weldability for Circularly Heat Input, Materials Science Forum, Vols. 580-582, pp. 667-670 (2008).

(87) S. Okano, M. Mochizuki and M. Toyoda, Angular Distortion Reduction by In-Process Control Welding Using Back Heating Sources, Materials Science Forum, Vols. 580-582, pp. 585-588 (2008).

(86) M. Mochizuki, S. Okano, G. B. An and M. Toyoda, Measurement of Through-Thickness Residual Stress in Primary Piping of Girth Welded Joint, Materials Science Forum, Vols. 580-582, pp. 577-580 (2008).

(85) J. Katsuyama, M. Mochizuki, H. Mori, W. Asano, G. B. An and M. Toyoda, Geometrical and Welding Conditions on Through-Thickness Residual Stress in Primary Piping of Girth Welded Joints, Materials Science Forum, Vols. 580-582, pp. 573-576 (2008).

(84) K. Mitani, M. Mochizuki and M. Toyoda, Investigation of Wall Thinning Measurement in Steel Plates by Electromagnetic Acoustic Resonance, Materials Science Forum, Vols. 580-582, pp. 113-116 (2008).

(83) H. Mori, J. Katsuyama, M. Mochizuki and K. Nishimoto, Effect of Residual Stress and Hardening on Grain Boundary Sliding in Welds of Low-carbon Stainless Steels with Surface Machining, Journal of Japan Society of Maintenology (in Japanese), Vol. 7, No. 1, pp. 36-41 (2008).

(82) Y. Mikami, M. Mochizuki and M. Toyoda, In-Process Control of Weld Distortion by Using Phase Transformation Effects, Mathematical Modelling of Weld Phenomena 8, Edited by H. Cerjak, TU Graz Publishing, Graz, Austria, pp. 981-1001 (2007).

(81) M. Mochizuki, Y. Mikami, and M. Toyoda, Study on Metallurgical and Mechanical Heterogeneity in Weld Materials Considering Multiple Heat Cycles and Phase Transformation, Mathematical Modelling of Weld Phenomena 8, Edited by H. Cerjak, TU Graz Publishing, Graz, Austria, pp. 287-294 (2007).

(80) K. Mitani, Y. Nakayama, E. Kanai, M. Mochizuki and M. Toyoda, Evaluation of Wall Thinning for Steel Plates by Electromagnetic Acoustic Resonance spectrum - Investigation of Thickness and Stress Evaluation Method for Steel Structures Using Electromagnetic Acoustic Transducer, Quarterly Journal of the Japan Welding Society (in Japanese), Vol. 25, No. 4, pp. 507-513 (2007).

(79) H. Mori, J. Katsuyama, M. Mochizuki, K. Nishimoto and M. Toyoda, Study on Mechanism of lntergranular Stress Corrosion Cracking and Analysis of Residual Stress and Work Hardening in Welds of Low-Carbon Austenitic Stainless Steel with Hard Surface Machining, Zairyo-to-Kankyo (in Japanese), Vol. 56, No. 12, pp. 568-575 (2007).

(78) M. Mochizuki, Y. Mikami, H. Yamasaki and M. Toyoda, Elastic Predicting Method of Weld Distortion of Large Structures Using Numerical Simulation Results by Thermal-Elastic-Plastic Analysis of Small Components, Welding in the World, Vol. 51, No. 11/12, pp. 60-64 (2007).

(77) Y. Mikami, Y. Nakatsu, Y. Hashiba, M. Mochizuki and M. Toyoda, Evaluation of Fracture Toughness of Multipass Weld Metal Considering Distribution of Microstructure, Journal of Construction Steel (in Japanese), Vol. 15, pp. 659-667 (2007).

(76) M. Mochizuki and M. Toyoda, Strategy of Considering Microstructure Effect on Weld Residual Stress Analysis, Transactions of the ASME, Journal of Pressure Vessel Technology, American Society of Mechanical Engineers, Vol. 129, No. 4, pp. 619-629 (2007).

(75) R. Higuchi, M. Mochizuki and M. Toyoda, FEM-MD Combined Method for Investigation on Effects of Microscopic Heterogeneity near Weld Zone on Strength Characteristics, Welding in the World, Vol. 51, Iss. 7/8, pp. 29-34 (2007).

(74) A. Tsumaya, K. Inoue, M. Mochizuki, H. Wakamatsu and E. Arai, Basic Study of the Plant Maintenance Model Considering Plant Improvement/Modification, Journal of Japan Society of Maintenology, Vol. 6, No. 1, pp. 34-39 (2007).

(73) M. Mochizuki and M. Toyoda, Weld Distortion Control during Welding Process with Reverse-Side Heating, Transactions of the ASME, Journal of Engineering Materials and Technology, American Society of Mechanical Engineers, Vol. 129, No. 2, pp. 265-270 (2007).

(72) S. Okano, M. Mochizuki and M. Toyoda, Study on Angular Distortion Reduction by Temperature Distribution Control Using Back Heating Source - Studies on Welding Distortion Control by Temperature Distribution Control Using Multiple Heat Sources (Report 2), Quarterly Journal of the Japan Welding Society (in Japanese), Vol. 25, No. 1, pp. 95-105 (2007).

(71) Y. Mikami, M. Mochizuki and M. Toyoda, Reduction of Angular Distortion by Transformation Expansion of Weld Metals in Joints with External Restraints - Welding Angular Distortion Control by Transformation Expansion of Weld Metals (Report 4), Quarterly Journal of the Japan Welding Society (in Japanese), Vol. 25, No. 1, pp. 74-79 (2007).

(70) Y. Mikami, M. Mochizuki and M. Toyoda, Effect of Heat Input Condition on Reduction of Angular Distortion
by Transformation Expansion of Weld Metals - Welding Distortion Control by Transformation Expansion of Weld Metals (Report 3), Quarterly Journal of the Japan Welding Society (in Japanese), Vol. 25, No. 1, pp. 68-73 (2007).

(69) Y. Mikami, M. Mochizuki and M. Toyoda, Effect of Characteristics of Transformation Expansion of Weld Metals
on Angular Distortion Behavior of Welded Joints - Welding Angular Distortion Control by Transformation Expansion of Weld Metals (Report 2), Quarterly Journal of the Japan Welding Society (in Japanese), Vol. 25, No. 1, pp. 59-67 (2007).

(68) M. Mochizuki, Control of Welding Residual Stress for Ensuring Integrity against Fatigue and Stress-Corrosion Cracking, Nuclear Engineering and Design, Vol. 237, Iss. 2, pp. 107-123 (2007).

(67) R. Higuchi, J. Katsuyama, M. Mochizuki and M. Toyoda, Numerical Analysis Method Considering Modeling for Morphology of Microstructure and Deformation in Close Vicinity to Grain Boundary for Evaluation of Strength Characteristics of Steels, Journal of the Society of Materials Science, Japan (in Japanese), Vol. 55, No. 12, pp. 1117-1124 (2006).

(66) O. Yasuda, H. Nagaki and M. Mochizuki, Development of Full Penetration Welding Process of T Joints Using MAG Welding, Journal of Construction Steel (in Japanese), Vol. 14, pp. 661-666 (2006).

(65) S. Okano, M. Mochizuki and M. Toyoda, Thermal Conductivity Theoretical Examination Concerning Characteristics of Welding Distortion Produced by Multiple Heat Sources - Studies on Welding Distortion Control by Temperature Distribution Control Using Multiple Heat Sources (Report 1), Quarterly Journal of the Japan Welding Society (in Japanese), Vol. 24, No. 4, pp. 324-330 (2006).

(64) Y. Mikami, Y. Morikage, M. Mochizuki and M. Toyoda, Measurement and Numerical Simulation of Angular Distortion of Fillet Welded T-joints - Welding Angular Distortion Control by Transformation Expansion of Weld Metals (Report 1), Quarterly Journal of the Japan Welding Society (in Japanese), Vol. 24, No. 4, pp. 312-323 (2006).

(63) M. Mochizuki, Evaluation of Through-Thickness Residual Stress in Multi-Pass Butt-Welded Joint by Using Inherent Strain, Science and Technology of Welding and Joining, Vol. 11, No. 5, pp. 496-501 (2006).

(62) M. Mochizuki, H. Yamasaki, S. Okano and M. Toyoda, Distortion Behavior of Fillet T-joint during In-Process Control Welding by Additional Cooling, Welding in the World, Vol. 50, No. 5/6, pp. 46-50 (2006).

(61) M. Mochizuki and K. Miyazaki, Surface Crack Propagation Analysis under Residual Stress Field, Welding in the World, Vol. 50, No. 5/6, pp. 38-45 (2006).

(60) M. Mochizuki, M. Inuzuka, H. Nishida, K. Nakata and M. Toyoda, Fracture Toughness of Structural Aluminum Thick-Plate Joints by Friction Stir Welding, Science and Technology of Welding and Joining, Vol. 11, No. 3, pp. 366-370 (2006).

(59) Y. Mikami, M. Mochizuki and M. Toyoda, Application of Numerical Simulation Considering the Effect of Phase Transformation to the Estimation of Hardness Distribution in Welds, Materials Science Forum, ISBN: 0-87849-996-2, Vol. 512, pp. 379-382 (2006).

(58) M. Toyoda, M. Mochizuki and Y. Mikami, Metallurgical and Mechanical Heterogeneity in Weld Materials Considering Multiple Heat Cycles and Phase Transformation, Materials Science Forum, ISBN: 0-87849-996-2, Vol. 512, pp. 19-24 (2006).

(57) K. Miyazaki and M. Mochizuki, Effects of Residual Stress Distribution and Geometry of Components on Stress Intensity Factor and Crack Growth Behavior of Surface Crack - Evaluation of SCC Growth under Residual Stress Field (Report 2), Quarterly Journal of the Japan Welding Society (in Japanese), Vol. 24, No. 1, pp. 78-86 (2006).

(56) K. Miyazaki, M. Numata, K. Saito and M. Mochizuki, Effects of Distance from Center of a Weld to Fixed End on
Residual Stress and Stress Intensity Factor of a Piping Weld - Evaluation of SCC Growth under Residual Stress Field (Report 1), Quarterly Journal of the Japan Welding Society (in Japanese), Vol. 24, No. 1, pp. 70-77 (2006).

(55) M. Mochizuki, J. Katsuyama, R. Higuchi and M. Toyoda, Study of Residual Stress Distribution at Start-Finish Point of Circumferential Welding Studied by 3D-FEM Analysis, Welding in the World, Vol. 49, No. 11/12, pp. 40-49 (2005).

(54) Y. Mikami, M. Mochizuki, Y. Hashiba, T. Hasegawa, S. Ohkita and M. Toyoda, Evaluation of Fraction of Microstructure and Hardness Distribution in Weld Metal Subjected to Multiple Thermal Cycles - Evaluation of Hardness Distribution in Welds by Numerical Simulation of Weld Thermal Cycles and Fraction of Microstructure (Report 2), Quarterly Journal of the Japan Welding Society (in Japanese), Vol. 23, No. 4, pp. 564-570 (2005).

(53) Y. Mikami, M. Mochizuki, T. Nakamura, K. Hiraoka and M. Toyoda, Numerical Simulation of Hardness Distribution in Welds of Ultra-Narrow Gap GMA Welding - Evaluation of Hardness Distribution in Welds by Numerical Simulation of Weld Thermal Cycles and Fraction of Microstructure (Report 1), Quarterly Journal of the Japan Welding Society (in Japanese), Vol. 23, No. 4, pp. 558-563 (2005).

(52) M. Mochizuki, G. B. An and M. Toyoda, Active In-Process Control of Welding Distortion by Reverse-Side Heating, Key Engineering Materials, Trans Tech Publication Ltd., Uetikon-Zuerich, Switzerland, ISBN 0-87849-978-4, Vols. 297-300, pp. 2784-2789 (2005).

(51) G. B. An, M. Ohata, M. Mochizuki, H.-S. Bang and M. Toyoda, Effect of Strength Mismatch on Ductile Crack Initiation Behavior of Notch Root under Static Loading, Key Engineering Materials, Trans Tech Publication Ltd., Uetikon-Zuerich, Switzerland, ISBN 0-87849-978-4, Vols. 297-300, pp. 756-761 (2005).

(50) K. Miya and M. Mochizuki, Codes and Standards with Social Demands, Journal of Japan Society of Maintenology, Vol. 4, No. 2, pp. 7-14 (2005).

(49) M. Mochizuki and M. Toyoda, Challenge to Active In-Process Control of Welding Distortion, Mathematical Modelling of Weld Phenomena 7, Edited by H. Cerjak, TU Graz Publishing, Graz, Austria, ISBN 3-901351-99-X, pp. 697-711 (2005).

(48) M. Mochizuki and M. Toyoda, Numerical Simulation of Stress-Strain Relation and Ductile-to-Brittle Transition in Welded Joints Subjected to Different Strain Rate, Mathematical Modelling of Weld Phenomena 7, Edited by H. Cerjak, TU Graz Publishing, Graz, Austria, ISBN 3-901351-99-X, pp. 435-461 (2005).

(47) H. Shirai, M. Urushizaki, M. Mochizuki and M. Toyoda, Reduction of Welding Deformation by Split Laser Beams - Study of Deformation Behavior by Laser Welding in Micron or Sub-Micron Area in Automobile Parts (Report 3), Quarterly Journal of the Japan Welding Society (in Japanese), Vol. 23, No. 1, pp. 137-142 (2005).

(46) M. Mochizuki, S. Matsushima, Y. Morikage, T. Kubo and M. Toyoda, Study on Residual Stress Reduction by Using Phase Transformation Phenomena in Welding Material - Studies on Numerical Simulation of Temperature, Microstructure, and Thermal Stress Histories in Welded Joints and Their Application to Welded Structures (Report 2), Quarterly Journal of the Japan Welding Society (in Japanese), Vol. 23, No. 1, pp. 112-121 (2005).

(45) M. Mochizuki, S. Matsushima, C. Thaulow and M. Toyoda, Fundamental Study on Thermal Stress Generation during Welding Heat Cycles - Studies on Numerical Simulation of Temperature, Microstructure, and Thermal Stress Histories in Welded Joints and Their Application to Welded Structures (Report 1), Quarterly Journal of the Japan Welding Society (in Japanese), Vol. 23, No. 1, pp. 103-111 (2005).

(44) M. Mochizuki and M. Toyoda, Thermal Stress History in High-Tensile Strength Steels during Weld Process, Journal de Physique IV, ISBN: 2-86883-785-9, Vol. 120, pp. 635-648 (2004).

(43) M. Mochizuki, T. Shintomi, Y. Hashimoto and M. Toyoda, Analytical Study on Deformation and Strength in HAZ-Softened Weld Joints of Fine-Grained Steels, Welding in the World, Vol. 48, No. 9/10, pp. 2-12 (2004).

(42) T. Kawabata, K. Arimochi, M. Ohata, M. Mochizuki and M. Toyoda, Investigation of Effective Damage Evaluation Under Repeated Prestraining of Tension and Compression in 780 MPa Class High Tensile Strength Steel Plate - Studies of Safety Against Fracture on 780 MPa Class High Tensile Strength Steel Plate after Prestrain (Report 3), Quarterly Journal of the Japan Welding Society (in Japanese), Vol. 22, No. 4, pp. 515-523 (2004).

(41) H. Shirai, M. Urushizaki, M. Mochizuki and M. Toyoda, Effect of Beam Profile at Focal Position on Welding Deformation - Study of Deformation Behavior by Laser Welding in Micron or Sub-Micron Level in Automobile Parts (Report 2), Quarterly Journal of the Japan Welding Society (in Japanese), Vol. 22, No. 4, pp. 509-514 (2004).

(40) M. Toyoda and M. Mochizuki, Control of Mechanical Properties in Structural Steel Welds by Coupling Simulation of Temperature, Microstructure, and Macro-Mechanics, Science and Technology in Advanced Materials, Vol. 5, Iss. 1-2, pp. 255-266 (2004).

(39) T. Kawabata, K. Arimochi, M. Ohata, M. Mochizuki and M. Toyoda, Investigation on Enhancement of Uniform Elongation in 780 MPa Class High Tensile Strength Steel Plate - Studies of Safety against Fracture on 780 MPa Class High Tensile Strength Steel Plate after Prestrain (Report 2), Quarterly Journal of the Japan Welding Society (in Japanese), Vol. 21, No. 3, pp. 433-441 (2003).

(38) T. Shintomi, Y. Hashimoto, I. Chikushi, M. Mochizuki and M. Toyoda, Deformation and Ductile Crack Initiation in Weld HAZ Softening Joints - Studies on Deformation and Strength in Welded Joints of Fine Grain Steel (Report 3), Quarterly Journal of the Japan Welding Society (in Japanese), Vol. 21, No. 3, pp. 411-418 (2003).

(37) T. Shintomi, I. Chikushi, Y. Hashimoto, M. Mochizuki and M. Toyoda, Prediction of Tensile Strength of Welded Joints for Fine Grain Steel with Softened HAZ - Studies on Deformation and Strength in Welded Joints of Fine Grain Steel (Report 2), Quarterly Journal of the Japan Welding Society (in Japanese), Vol. 21, No. 3, pp. 404-410 (2003).

(36) T. Shintomi, I. Chikushi, Y. Hashimoto, M. Ohata, M. Mochizuki and M. Toyoda, Effect of Weld HAZ Softening on Tensile Strength - Studies on Deformation and Strength in Welded Joints of Fine Grain Steel (Report 1), Quarterly Journal of the Japan Welding Society (in Japanese), Vol. 21, No. 3, pp. 397-403 (2003).

(35) H. Shirai, M. Urushizaki, S. Sawamoto, M. Mochizuki and M. Toyoda, Analysis of Bending Deformation Behavior in Cylindrical Parts by Circumferential Welding - Study of Deformation Behavior by Laser Welding in Micron or Sub-Micron Level in Automobile Parts (Report 1), Quarterly Journal of the Japan Welding Society (in Japanese), Vol. 21, No. 3, pp. 389-396 (2003).

(34) M. Mochizuki, M. Kohara, H. Shimanuki, Y. Hagiwara and M. Toyoda, Analytical Study on Effects of Microscopic Heterogeneity on Crack Generation in Ferrite/Martensite Dual-Phase Steels, Journal of the Society of Materials Science, Japan (in Japanese), Vol. 52, No. 8, pp. 939-945 (2003).

(33) M. Mochizuki, M. Kohara, H. Shimanuki, Y. Hagiwara and M. Toyoda, Crack Initiation and Propagation in Ferrite/Martensite Dual-Phase Steels with Microscopic Heterogeneity by Fracture Toughness Tests, Journal of the Society of Materials Science, Japan (in Japanese), Vol. 52, No. 8, pp. 932-938 (2003).

(32) M. Mochizuki, Y. Mikami and M. Toyoda, Analytical Study on Effects of Welding Deposition Sequence on Microstructure and Hardness in Beam-to-Column Welded Connection of Steel Framed Structures - Studies on Relation between Joint Performance and Welding Heat Cycles in Welded Joints (Report 2), Quarterly Journal of the Japan Welding Society (in Japanese), Vol. 21, No. 1, pp. 54-61 (2003).

(31) M. Mochizuki and M. Toyoda, Effects of Welding Multiple Heat Cycles on Joint Performance in Beam-to-Column Welded Connection of Steel Framed Structures - Studies on Relation between Joint Performance and Welding Heat Cycles in Welded Joints (Report 1), Quarterly Journal of the Japan Welding Society (in Japanese), Vol. 21, No. 1, pp. 46-53 (2003).

(30) M. Mochizuki, M. Toyoda, P. Pasquale, C. Veneziano and W. Burget, Numerical Simulation of Welding Heat Cycles during Multi-Pass Welding and their Effects on Joint Performance, Mathematical Modelling of Weld Phenomena 6, Edited by H. Cerjak, Series Edited by H. K. D. H. Bhadeshia, Maney Publishing, London, United Kingdom, ISBN 1-902653-56-4, pp. 671-683 (2002).

(29) M. Mochizuki, K. Enomoto and M. Toyoda, Residual Stress Control for Assuring Integrity against Fatigue and Stress-Corrosion Cracking in Welded Components, Mathematical Modelling of Weld Phenomena 6, Edited by H. Cerjak, Series Edited by H. K. D. H. Bhadeshia, Maney Publishing, London, United Kingdom, ISBN 1-902653-56-4, pp. 539-571 (2002).

(28) M. Mochizuki, Y. Mikami and M. Toyoda, Evaluation of Mechanical Properties in Welded Joints by Numerical Welding Simulation, Journal of Construction Steel (in Japanese), Vol. 10, pp. 35-42 (2002).

(27) T. Kawabata, K. Arimochi, M. Ohata, M. Mochizuki and M. Toyoda, Behavior of Deformation in 780 MPa Class High Tensile Strength Steel Plate after Prestrain - Studies of Safety against Fracture on 780 MPa Class High Tensile Strength Steel Plate after Prestrain (Report 1), Quarterly Journal of the Japan Welding Society (in Japanese), Vol. 20, No. 3, pp. 398-407 (2002).

(26) K. Miyazaki, M. Mochizuki, S. Kanno, M. Hayashi, M. Shiratori and Q. Yu, Analysis of Stress Intensity Factor due to Surface Crack Propagation in Residual Stress Fields Caused by Welding - Comparison of Influence Function Method and Inherent Strain Analysis, JSME International Journal (Series A), Vol. 45, No. 2, pp. 199-207 (2002).

(25) M. Mochizuki, G. B. An, T. Ohmura and M. Toyoda, Strength and Fracture in Undermatched Joint by Dynamic Loading - Studies on Characteristics of Dynamic Deformation and Fracture in Welded Joint with Strength Heterogeneity (Report 2), Quarterly Journal of the Japan Welding Society (in Japanese), Vol. 19, No. 3, pp. 547-555 (2001).

(24) M. Mochizuki, G. B. An, T. Ohmura and M. Toyoda, Thermal Elastic-Plastic Stress and Strain Analysis Considering Temperature Rise due to Plastic Deformation by Dynamic Loading in Undermatched Joint - Studies on Characteristics of Dynamic Deformation and Fracture in Welded Joint with Strength Heterogeneity (Report 1), Quarterly Journal of the Japan Welding Society (in Japanese), Vol. 19, No. 3, pp. 537-546 (2001).

(23) M. Mochizuki and M. Toyoda, Numerical Analysis of Residual Stress in Welded Structures Using Inherent Strain, Mathematical Modelling of Weld Phenomena 5, Edited by H. Cerjak, Series Edited by H. K. D. H. Bhadeshia, IOM Communications, London, United Kingdom, ISBN 1-86125-115-7, pp. 549-580 (2001).

(22) M. Mochizuki, M. Ohata, S. Takeno and M. Toyoda
Characteristics of Welding Distortion and Its In-Process Control by Ahead Heating Method in Aluminum Alloy Welded Joint, Journal of Light Metal Welding and Construction (in Japanese), Vol. 38, No. 11, pp. 536-543 (2000).

(21) T. Hashimoto and M. Mochizuki, Modeling of Helium Bubble Formation During Welding of Irradiated Stainless Steels, Effects of Radiation on Materials, ASTM STP 1366, Edited by M. L. Hamilton, A. S. Kumar, S. T. Rosinski and M. L. Grossbeck, American Society for Testing and Materials, West Conshohocken, PA, USA, ISBN-0-8031-2852-5, pp. 973-987 (2000).

(20) M. Mochizuki, M. Hayashi and T. Hattori, Residual Stress Distribution Depending on Welding Sequence in Multi-Pass Welded Joints with X-Shaped Groove, Transactions of the ASME, Journal of Pressure Vessel Technology, American Society of Mechanical Engineers, Vol. 122, No. 1, pp. 27-32 (2000).

(19) M. Mochizuki, T. Hattori and K. Nakakado, Residual Stress Reduction and Fatigue Strength Improvement by Controlling Welding Pass Sequences, Transactions of the ASME, Journal of Engineering Materials and Technology, American Society of Mechanical Engineers, Vol. 122, No. 1, pp. 108-112 (2000).

(18) M. Mochizuki, M. Hayashi and T. Hattori, Numerical Analysis of Welding Residual Stress and Its Verification Using Neutron Diffraction Measurement, Transactions of the ASME, Journal of Engineering Materials and Technology, American Society of Mechanical Engineers, Vol. 122, No. 1, pp. 98-103 (2000).

(17) M. Mochizuki, M. Hayashi and T. Hattori, Residual Stress Analysis by Simplified Inherent Strain at Welded Pipe Junctures in a Pressure Vessel, Transactions of the ASME, Journal of Pressure Vessel Technology, American Society of Mechanical Engineers, Vol. 121, No. 4, pp. 353-357 (1999).

(16) K. Miyazaki, S. Kanno, M. Mochizuki, M. Hayashi, M. Shiratori and Q. Yu, Evaluation of Stress Intensity Factor due to Surface Crack Propagation by Using Influence Function Method and Inherent Strain Analysis in Residual Stress Fields Caused by Welding, Transactions of the Japan Society of Mechanical Engineers (in Japanese), Vol. 65A, No. 636, pp. 1709-1715 (1999).

(15) M. Mochizuki, T. Hattori, M. Zen, J. Yamamoto and K. Nakakado, Simplified Analysis of Welding Residual Stress in a Box Structure Fabricated with Plural Welded Joints, Transactions of the Japan Society of Mechanical Engineers (in Japanese), Vol. 65A, No. 633, pp. 989-995 (1999).

(14) M. Mochizuki and M. Hayashi, A Simplified Method for Residual Stress Analysis in Welded Structures with Complicated Shape, Journal of the Japan High Pressure Institute (in Japanese), Vol. 37, No. 1, pp. 27-37 (1999).

(13) M. Mochizuki, M. Hayashi and T. Hattori, Comparison of Five Evaluation Methods of Residual Stress in a Welded Pipe Joint, JSME International Journal (Series A), Vol. 42, No. 1, pp. 104-110 (1999).

(12) M. Mochizuki, M. Zen, T. Hattori, M. Watanabe, K. Nakakado and A. Hashimoto, Improvement of Fatigue Strength through Residual Stress Reduction by Controlling the Sequence of Welding Pass, Transactions of the Japan Society of Mechanical Engineers (in Japanese), Vol. 64A, No. 626, pp. 2514-2520 (1998).

(11) M. Mochizuki, M. Hayashi and T. Hattori, Welding Residual Stress Estimation by Inherent Strain Analysis and Thermal Elastic Plastic Analysis and Its Verification Using Neutron Diffraction Measurement, Transactions of the Japan Society of Mechanical Engineers (in Japanese), Vol. 63A, No. 612, pp. 1675-1680 (1997).

(10) M. Mochizuki, M. Hayashi, M. Nakagawa, N. Tada and S. Shimizu, A Simplified Analysis of Residual Stress at Welded Joints Between Plate and Penetrating Pipe, JSME International Journal (Series A), Vol. 40, No. 1, pp. 8-14 (1997).

(9) M. Mochizuki, M. Hayashi and T. Hattori, Effect of Welding Sequence on Residual Stress in Multi-Pass Butt-Welded Pipe Joints, Transactions of the Japan Society of Mechanical Engineers (in Japanese), Vol. 62A, No. 604, pp. 2719-2725 (1996).

(8) K. Enomoto, K. Hirano, M. Mochizuki, K. Kurosawa, H. Saito and E. Hayashi, Improvement of Residual Stress on Material Surface by Water Jet Peening, Journal of the Society of Materials Science, Japan (in Japanese), Vol. 45, No. 7, pp. 734-739 (1996).

(7) M. Mochizuki, M. Hayashi, M. Nakagawa, N. Tada and S. Shimizu, Residual Stress Estimation at Welded Joint of a Pipe Penetrating a Thick Plate, Transactions of the Japan Society of Mechanical Engineers (in Japanese), Vol. 62A, No. 597, pp. 1250-1255 (1996).

(6) M. Mochizuki, N. Saito, S. Sakata and H. Uozumi, Study on Residual Stress at Butt-Welded Pipe Joints and Plate Joints Using Inherent Strain Analysis, Transactions of the Japan Society of Mechanical Engineers (in Japanese), Vol. 62A, No. 595, pp. 808-813 (1996).

(5) M. Mochizuki, N. Saito, K. Enomoto, S. Sakata and H. Saito, Study on Internal Residual Stress of Multi-Pass Butt-Welded Plate Joint Using Inherent Strain Analysis, Transactions of the Japan Society of Mechanical Engineers (in Japanese), Vol. 61A, No. 587, pp. 1568-1573 (1995).

(4) M. Mochizuki, K. Enomoto, N. Okamoto, S. Saito and E. Hayashi, Study on Production Mechanism of Welding Residual Stress at the Juncture of a Pipe Penetrating a Thick Plate, Quarterly Journal of the Japan Welding Society (in Japanese), Vol. 12, No. 4, pp. 561-567 (1994).

(3) M. Mochizuki, K. Enomoto, N. Okamoto, H. Saito and E. Hayashi, Welding Residual Stresses at the Intersection of a Small Diameter Pipe Penetrating a Thick Plate, Nuclear Engineering and Design, Vol. 144, No. 3, pp. 439-447 (1993).

(2) Y. Ueda, M. G. Yuan, M. Mochizuki, S. Umezawa and K. Enomoto, Experimental Verification for Predicting Method of Welding Residual Stresses in T-Joints Using Inherent Strain, A Predicting Method of Welding Residual Stress Using Source of Residual Stress (Report 4), Quarterly Journal of the Japan Welding Society (in Japanese), Vol. 11, No. 2, pp. 327-333 (1993).

(1) T. Hoshide, M. Mochizuki and T. Inoue, Fracture Behavior of Ceramic Coating Produced by Detonation Method Under Biaxial Stresses, Journal of the Society of Materials Science, Japan (in Japanese), Vol. 39, No. 439, pp. 387-392 (1990).

2. Proceedings (Full Paper)

2.1 Proceedings of International Conference with Peer Review

(68) M. Mochizuki, Effect of Weld HAZ Mis-Matching on Joint Performances in High Chromium Steel Welded Joint, Proceedings of the 20th International Conference on Nuclear Engineering, Anaheim, USA, ICONE20POWER2012-54699, in press (2012).　

(67) M. Mochizuki and T. Kawabata, Effect of Undermatched Weld on Deformation and Brittle Fracture Behaviors in High-Tensile Strength Steel Plate Welded Joint, Proceedings of the 2012 ASME Pressure Vessels and Piping Conference, Toronto, Canada, PVP2012-78813 in press (2012).　

(66) M. Mochizuki, H. Kitano and S. Okano, Improvement of Residual Stress Determination by Deep Hole Drilling Considering Plastic Deformation, Proceedings of the 2012 ASME Pressure Vessels and Piping Conference, Toronto, Canada, PVP2012-78812, in press (2012).　

(65) F. Iwamatsu, K. Miyazaki and M. Mochizuki, Estimation of SCC Crack Growth Behavior under Weld Residual Stress in the Bottom of a Reactor Pressure Vessel by Finite Element Analysis, Proceedings of the 2012 ASME Pressure Vessels and Piping Conference, Toronto, Canada, PVP2012-78471, in press (2012).　

(64) M. Iyota, Y. Mikami, T. Hashimoto, K. Taniguchi, R. Ikeda and M. Mochizuki, Effect of Electrode Force and Transformation Expansion on Welding Distortion and Residual Stress of Resistance Spot Welded High Strength Steel Sheet, Proceedings of the 3rd International Conference on Distortion Engineering, Bremen, Germany (2011).　

(63) N. Ochi, S. Okano, F. Miyasaka, M. Tanaka and M. Mochizuki, Integrated Simulation Model for GMA Welding by Coupling Arc Plasma and Bead Formation with Thermal Distortion, Proceedings of the 19th International Conference on Nuclear Engineering, Makuhari, Japan, ICONE19-43349 (2011).　

(62) H. Kitano, S. Okano and M. Mochizuki, Measurement of Non-equibiaxial Residual Stress Field by Indentation Technique Using Asymmetric Indenter, Proceedings of the 19th International Conference on Nuclear Engineering, Makuhari, Japan, ICONE19-43348 (2011).　

(61) R. Ihara, T. Hashimoto and M. Mochizuki, Residual Stress and Microstructure Evolution by Manufacturing Processes for Welded Pipe Joint in Austenitic Stainless Steel Type 316L, Proceedings of the 19th International Conference on Nuclear Engineering, Makuhari, Japan, ICONE19-43347 (2011).　

(60) T. Hashimoto, S. Okano, S. Hirano, M. Mochizuki and K. Nishimoto, Residual Stress by X-ray Diffraction and Microstructure for Multi-pass Girth Welded Pipe Joint in Austenitic Stainless Steel Type 316L, Proceedings of the 2011 ASME Pressure Vessels and Piping Conference, Baltimore, USA, PVP2011-57434 (2011).　

(59) H. Kitano, S. Okano and M. Mochizuki, Deformation State Evaluation around Deep Drilled Hole after Three-Dimensional Stress Release, Proceedings of the 2011 ASME Pressure Vessels and Piping Conference, Baltimore, USA, PVP2011-57193 (2011).　

(58) T. Hashimoto, Y. Osawa, M. Kameyama, S. Hirano, N. Chigusa, K. Saida, M. Mochizuki and K. Nishimoto, Long Term Stability of Compressive Residual Stress Introduced in Alloy 600 by Water Jet Peening under Elevated Temperature Environment, Proceedings of the 2011 ASME Pressure Vessels and Piping Conference, Baltimore, USA, PVP2011-57091 (2011).　

(57) S. Itoh, M. Hata, M. Shibahara and M. Mochizuki, Application of Inherent Strain Analysis Using Idealized Explicit FEM for Prediction of Welding Deformation in Ship Block Building, Proceedings of the 21st International Offshore and Polar Engineering Conference, Vol. 4, pp. 111-116, 11TPC-786, Maui, Hawaii (2011).　　

(56) A. Kawaguchi, S. Itoh, M. Mochizuki and M. Kameyama, Large-Scale Computation of Welding Residual Stress, Proceedings of the Joint International Conference on Supercomputing in Nuclear Applications and Monte Carlo 2010, OC2-2-II-4, Tokyo, Japan (2010).　

(55) M. Mochizuki, S. Kanno, S. Shimizu and Y. Daitou, Diagnostics of Nuclear Power Plant Components due to Thickness Measurement by Using Digital Radiography, Proceedings of the 2010 ASME Pressure Vessels and Piping Conference, Seattle, USA, PVP2010-25999 (2010).　

(54) M. Mochizuki, Weld HAZ Mis-Matching Design for Joint Performances in High Chromium Steel Welded Pipe-Joint for Sodium Cooled Fast Breeder Reactor, Proceedings of the 2010 ASME Pressure Vessels and Piping Conference, Seattle, USA, PVP2010-25903 (2010).　

(53) M. Mochizuki and S. Itoh, Million-Finite-Element-Order Large-Scale Computation of Residual Stress in Complicated Weld Structures, Proceedings of the 2010 ASME Pressure Vessels and Piping Conference, Seattle, USA, PVP2010-25902 (2010).　

(52) M. Mochizuki and S. Okano, Coupling Computation between Weld Mechanics and Arc Plasma Processes, Proceedings of the 2010 ASME Pressure Vessels and Piping Conference, Seattle, USA, PVP2010-25901 (2010).　

(51) M. Mochizuki, H. Mori and J. Katsuyama, Mechanism Study on IGSCC by Analyzing Residual Stress and Work Hardening in Welds of Low-Carbon Austenitic Stainless Steel with Surface Machining, Proceedings of the 2010 ASME Pressure Vessels and Piping Conference, Seattle, USA, PVP2010-25900 (2010).　

(50) M. Mochizuki and Y. Mikami, Prediction of SCC Initiation in Weld Components by Multi-Scale Analysis Incorporating Crystal Plasticity, Proceedings of the 2010 ASME Pressure Vessels and Piping Conference, Seattle, USA, PVP2010-25899 (2010).　

(49) K. Sogabe, Y. Mikami, T. Kurashiki and M. Mochizuki, An Application of Multi-Scale Analysis to the Evaluation of Microscopic Residual Stress in the Welding Joint, Proceedings of the 12th International Conference on Pressure Vessel Technology, Jeju, Korea, No. WRS4-2, pp. 505-511 (2009).

(48) J. Yamada, S. Okano, H. Mori, M. Mochizuki and K. Nishimoto, Thermal Stress and Strain Behavior during Laser Processing in Low Carbon Austenitic Stainless Steel for Joint Performance, Proceedings of the 12th International Conference on Pressure Vessel Technology, Jeju, Korea, No. WRS3-2, pp. 403-409 (2009).

(47) R. Ihara, J. Katsuyama, K. Onizawa, T. Hashimoto, Y. Mikami, M. Mochizuki and M. Toyoda, Prediction of Hardness and Residual Stress Distribution Generated by Surface Machining and Welding in Low-Carbon Austenitic Stainless Steel, Proceedings of the 12th International Conference on Pressure Vessel Technology, Jeju, Korea, No. WRS2-4, pp. 224-230 (2009).

(46) S. Itoh, M. Shibahara, M. Mochizuki and H. Murakawa, Prediction of Welding Deformation of Shell and Multiple-Pipe Components, Proceedings of the 12th International Conference on Pressure Vessel Technology, Jeju, Korea, No. WRS1-5, pp. 72-79 (2009).

(45) M. Iyota, Y. Mikami, Y. Inoue, T. Kasuya and M. Mochizuki, Cold Cracking Prevention in Pressure Vessel Steels by Low-Temperature Transformation Expansion of Weld Metals, Proceedings of the 12th International Conference on Pressure Vessel Technology, Jeju, Korea, No. WRS1-4, pp. 65-71 (2009).

(44) M. Mochizuki, J. Katsuyama, R. Ihara, Y. Mikami and K. Onizawa, Crack Growth Analysis of Stress Corrosion Cracking under Combined Stress Field due to Welding and Surface Machining, Proceedings of the 2009 ASME Pressure Vessels and Piping Conference, Prague, Czech, PVP2009-77706 (2009).

(43) M. Mochizuki, S. Okano and H. Shirai, Weld Residual Stress and Distortion by Considering Process Mechanics, Proceedings of the 2009 ASME Pressure Vessels and Piping Conference, Prague, Czech, PVP2009-77617 (2009).

(42) M. Mochizuki and Y. Mikami, Heterogeneous Microstructure Effect on Residual Stress and Fatigue Crack Resistance in Dual-Phase Materials, Proceedings of the 2009 ASME Pressure Vessels and Piping Conference, Prague, Czech, PVP2009-77446 (2009).

(41) H. Kitano, S. Okano and M. Mochizuki, Effects of HAZ Softening on Tensile Strength Limit in Girth-Welded Pipe Joints, Proceedings of the 2009 ASME Pressure Vessels and Piping Conference, Prague, Czech, PVP2009-77445 (2009).

(40) M. Mochizuki and R. Higuchi, Stress-Strain Relationship in Microstructural Region Using Triangular Pyramidal Indenter, Proceedings of the 19th International Offshore and Polar Engineering Conference, Osaka, Japan, ISOPE-2009-TPC-806 (2009).

(39) S. Okano, M. Mochizuki, M. Toyoda and T. Ueyama, Experimental Study on Thermal Distortion Behavior during In-Process Control Welding by Additional Cooling, Proceedings of the 19th International Offshore and Polar Engineering Conference, Osaka, Japan, ISOPE-2009-TPC-711 (2009).

(38) J. Yamada, S. Okano, H. Mori, M. Mochizuki and K. Nishimoto, Numerical Study on Strain Behavior During Solidification Evaluation of Solidification Cracking Susceptibility in Low Carbon Austenitic Stainless Steel Laser Weld, Proceedings of the 19th International Offshore and Polar Engineering Conference, Osaka, Japan, ISOPE-2009-TPC-704 (2009).

(37) S. Itoh, S. Okano, M. Mochizuki and H. Murakawa, Influence of Initial Residual Stress by Rolling Process on Welding Distortion of Stiffened Plate, Proceedings of the 19th International Offshore and Polar Engineering Conference, Osaka, Japan, ISOPE-2009-TPC-650 (2009).

(36) Y. Mikami, A. Inao, K. Nakashima, H. Shimanuki, M. Mochizuki and M. Toyoda, Transformation-Induced Microscopic Residual Stress in Ferrite-Martensite Lamellar Steels and Its Influence on Fatigue Crack Propagation Paths, Proceedings of the 19th International Offshore and Polar Engineering Conference, Osaka, Japan, ISOPE-2009-TPC-550 (2009).

(35) M. Mochizuki, Y. Mikami and M. Iyota, Effect of Low Temperature Transformation Expansion on Restraint Stress of High Strength Steel Welds, Proceedings of the 19th International Offshore and Polar Engineering Conference, Osaka, Japan, ISOPE-2009-TPC-549 (2009).

(34) T. Sato, Y. Mikami, M. Mochizuki, N. Suzuki and M. Toyoda, Parametric Study on the Effect of Geometric Imperfections on the Bending Capacity of High-Strength Linepipes, Proceedings of the 7th International Pipeline Conference, Calgary, Canada, IPC2008-64544 (2008).

(33) W. Asano, J. Katsuyama, K. Onizawa, M. Mochizuki and M. Toyoda, Effect of Surface Machining and Butt-Welding on Residual Stress and Hardness of Type 316L Stainless Steel Pipes, Proceedings of the 2008 ASME Pressure Vessels and Piping Conference, Chicago, USA, PVP2008-61441 (2008).

(32) Y. Morikage, T. Kubo, K. Yasuda, Y. Mikami and M. Mochizuki, Effect of Transformation Temperature of Weld Metal on Welding Distortion, Proceedings of the 27th International Conference on Offshore Mechanics and Arctic Engineering, Estoril, Portugal, OMAE2008-57709 (2008).

(31) J. Katsuyama, W. Asano, K. Onizawa, M. Mochizuki and M. Toyoda, Crack Growth Analyses of SCC under Various Residual Stress Distributions near the Piping Butt-Welding, Proceedings of the 2007 ASME Pressure Vessels and Piping Conference, San Antonio, USA, PVP2007-26574 (2007).

(30) M. Mochizuki, R. Higuchi, J. Katsuyama and M. Toyoda, Evaluation of Strength Characteristics Considering Microscopic Heterogeneity of Structural Steels and Weld Zone by Using FEM-MD Coupling Method, Proceedings of the 2007 ASME Pressure Vessels and Piping Conference, San Antonio, USA, PVP2007-26573 (2007).

(29) K. Mitani, M. Mochizuki and M. Toyoda, Study on Thickness and Actual Stress Measurement of Steel Structures Using Electromagnetic Acoustic Transducer, Proceedings of the 2007 ASME Pressure Vessels and Piping Conference, San Antonio, USA, PVP2007-26460 (2007). 

(28) J. Katsuyama, M. Mochizuki and M. Toyoda, Distribution of Residual Stress and Work Hardening by Surface-Machining near Circumferential Welding Zone, Proceedings of the 2006 ASME Pressure Vessels and Piping Conference, Vancouver, Canada, PVP2006-ICPVT11-93490 (2006).

(27) M. Mochizuki, J. Katsuyama and M. Toyoda, Effect of Geometrical and Welding Conditions on Through-Thickness Residual Stress, Proceedings of the 2006 ASME Pressure Vessels and Piping Conference, Vancouver, Canada, PVP2006-ICPVT11-93489 (2006).

(26) M. Mochizuki, R. Higuchi, J. Katsuyama and M. Toyoda, FEM-MD Coupling Simulation for Strength and Fracture Analyses near Grain Boundary Zone of Structural Steels, Proceedings of the 2006 ASME Pressure Vessels and Piping Conference, Vancouver, Canada, PVP2006-ICPVT11-93492 (2006).

(25) Y. Mikami, Y. Morikage, M. Mochizuki and M. Toyoda, Numerical Simulation of Welding Distortions of T-Joints with Low-Temperature Transformation Welding Wire, Proceedings of the 1st International Conference on Distortion Engineering, Bremen, Germany, ISBN 3-88722-653-4, pp. 453-460 (2005).

(24) Y. Morikage, T. Kubo, K. Yasuda, K. Amano, Y. Mikami, M. Mochizuki and M. Toyoda, Welding-Distortion Phenomena of T-joint Using Low-Temperature Transformation Welding Wire, Proceedings of the 1st International Conference on Distortion Engineering, Bremen, Germany, ISBN 3-88722-653-4, pp. 447-452 (2005).

(23) J. Katsuyama, M. Mochizuki, R. Higuchi and M. Toyoda, Parametric FEM Evaluation of Residual Stress by Circumferential Welding for Austenitic Stainless Steel, Proceedings of the 2005 ASME Pressure Vessels and Piping Division Conference, Denver, USA, PVP2005-71440 (2005).

(22) K. Miyazaki, M. Numata, K. Saito and M. Mochizuki, Effect of Distance from the Center of Weld to the Fixed End on Residual Stress and Stress Intensity Factor of the Piping Weld, Proceedings of the 2005 ASME Pressure Vessels and Piping Division Conference, Denver, USA, PVP2005-71461 (2005).

(21) K. Miyazaki and M. Mochizuki, Effects of Residual Stress Distribution and Geometry of Components on the Stress Intensity Factor of Surface Crack, Proceedings of the 2005 ASME Pressure Vessels and Piping Division Conference, Denver, USA, PVP2005-71462 (2005).

(20) M. Mochizuki, Y. Mikami, Y. Morikage and M. Toyoda, Effect of Material Properties on Welding Distortion History, Proceedings of the 2005 ASME Pressure Vessels and Piping Division Conference, Denver, USA, PVP2005-71466 (2005).

(19) M. Mochizuki and M. Toyoda, Effect of Bead Deposition by Repair Welding on Residual Stress in Pipe Welds, Proceedings of the 2004 ASME Pressure Vessels and Piping Conference, San Diego, USA, ISBN 0-7918-4671-1, Vol. 479, pp. 109-115, PVP2004-2654 (2004).

(18) M. Mochizuki, M. Toyoda, T. Kubo and Y. Morikage, Residual Stress Reduction by Using Weld Metal with Property of Low-Temperature Phase Transformation, Proceedings of the 2004 ASME Pressure Vessels and Piping Conference, San Diego, USA, ISBN 0-7918-4671-1, Vol. 479, pp. 77-83, PVP2004-2650 (2004).

(17) M. Mochizuki and M. Toyoda, Strategy of Considering Microstructural Effect on Weld Residual Stress Analysis, Proceedings of the 2004 ASME Pressure Vessels and Piping Conference, San Diego, USA, ISBN 0-7918-4671-1, Vol. 479, pp. 63-75, PVP2004-2649 (2004).

(16) M. Mochizuki, K. Miyazaki and M. Toyoda, How Validates Residual Stress Effect on Fatigue Strength and SCC Evaluations ?, Proceedings of the 2004 ASME Pressure Vessels and Piping Conference, San Diego, USA, ISBN 0-7918-4671-1, Vol. 479, pp. 25-41, PVP2004-2645 (2004).

(15) M. Mochizuki, M. Inuzuka, H. Nishida and M. Toyoda, Mechanical Properties and Fracture Toughness of Aluminum Vessels by Friction Stir Welding, Proceedings of the 2004 ASME Pressure Vessels and Piping Conference, San Diego, USA, Vol. 474, pp. 17-22, PVP2004-2296 (2004).

(14) M. Mochizuki and M. Toyoda, High-Cycle Fatigue Strength and Residual Stress in Welded Joints of Structural Steels, Proceedings of the 2004 ASME Pressure Vessels and Piping Conference, San Diego, USA, ISBN 0-7918-4667-9, Vol. 472, pp. 137-143, PVP2004-2985 (2004).

(13) M. Mochizuki and M. Toyoda, Residual Stress by Repair Welds, Proceedings of the 11th International Conference on Nuclear Engineering, Tokyo, Japan, ICONE11-36141 (2003).

(12) M. Mochizuki, G. B. An and M. Toyoda, Evaluation of Ductile-to-Brittle Transition and Crack Initiation in Welded Joints by Numerical Simulation, Proceedings of the 11th International Conference on Nuclear Engineering, Tokyo, Japan, ICONE11-36140 (2003).

(11) M. Mochizuki and M. Toyoda, Coupling Phenomena of Temperature, Microstructure, and Stress-Strain Fields during Weld Process, Proceedings of the 11th International Conference on Nuclear Engineering, Tokyo, Japan, ICONE11-36139 (2003).

(10) M. Mochizuki, G. B. An and M. Toyoda, Effects of Plastic Constraint and Strain Rate on Characteristics of Strength and Fracture in Undermatched Joints, Proceedings of the 2002 ASME Pressure Vessels and Piping Conference, Vancouver, Canada, Vol. 434, pp. 187-200 (2002).

(9) M. Mochizuki, S. Matsushima, M. Toyoda, Z. Zhang, O. Gundersen and C. Thaulow, Generation Behavior of Thermal and Residual Stresses due to Phase Transformation during Welding Heat Cycles, Proceedings of the 2002 ASME Pressure Vessels and Piping Conference, Vancouver, Canada, Vol. 434, pp. 123-129 (2002).

(8) M. Mochizuki, N. Takahashi and M. Toyoda, Three-Dimensional Analysis of In-Process Distortion Control in Fillet Welded Joints by Additional Cooling, Proceedings of the 2002 ASME Pressure Vessels and Piping Conference, Vancouver, Canada, Vol. 434, pp. 81-88 (2002).

(7) M. Mochizuki and M. Toyoda, In-Process Control of Welding Distortion by Reverse-Side Heating in Fillet Welds, Proceedings of the 2000 ASME Pressure Vessels and Piping Conference, Seattle, USA, Vol. 410-1, pp. 29-36 (2000).

(6) M. Mochizuki, T. Hattori and M. Hayashi, A New and Simplified Method for Estimating Residual Stress in Welded Structures with Complicated Shape Using Inherent Strain, Transactions of the 14th International Conference on Structural Mechanics in Reactor Technology, Lyon, France, Vol. 4, Div. G, pp. 77-84 (1997).

(5) K. Hirano, K. Enomoto, M. Mochizuki, M. Hayashi, E. Hayashi and S. Shimizu, Improvement of Residual Stress on Material Surface by Water Jet Peening, Transactions of the 14th International Conference on Structural Mechanics in Reactor Technology, Lyon, France, Vol. 2, Div. D, pp. 361-368 (1997).

(4) M. Mochizuki, M. Hayashi, M. Nakagawa, N. Tada and S. Shimizu, Residual Stress Estimation at Welded Juncture of Small Diameter Pipe Penetrating Pressure Vessel Using Inherent Strain, Proceedings of the 8th International Conference on Pressure Vessel Technology, Montreal, Canada, Vol. 2, No. H1070B, pp. 237-243 (1996).

(3) M. Mochizuki, T. Hattori and M. Hayashi, A Simplified Method for Estimating Residual Stress in Welded Structures Using Inherent Strain, Proceedings of the 4th European Conference on Residual Stress, Cluny, France, Vol. 1, pp. 445-454 (1996).

(2) M. Mochizuki, N. Saito, K. Enomoto, S. Sakata and H. Saito, A Study on Residual Stress of Butt-Welded Plate Joint Using Inherent Strain Analysis, Transactions of the 13th International Conference on Structural Mechanics in Reactor Technology, Porto Alegre, Brazil, Vol. 2, Div. F, pp. 243-248 (1995).

(1) F. Takahashi, M. Koike, M. Oda and M. Mochizuki, A High Accuracy Ultrasonic Measurement Method for Nondestructive Evaluation of Residual Stress in Welded Pipings, Proceedings of the 13th International Conference on Nondestructive Evaluation in Nuclear and Pressure Vessel Industries, Kyoto, Japan, pp. 471-476 (1995).

2.2 Proceedings of International Conference

(74) M. Mochizuki, Innovative Computational Simulation of Weld Residual Stress from Mega- to Micro-Structures, Proceedings of the 13th International Conference on Pressure Vessel Technology, London, United Kingdom, No. S1-DA1-P3 (2012).　

(73) R. Ihara, T. Hashimoto and M. Mochizuki, Effect of Microstructure Evolution due to Processing History of Piping on Residual Stress Distribution in Austenitic Stainless Steel, Transactions of the 21st International Conference on Structural Mechanics in Reactor Technology, New Deli, India, Div-II-472 (2011).　

(72) M. Iyota, Y. Mikami, T. Hashimoto, K. Taniguchi, R. Ikeda and M. Mochizuki, The Effect of Martensitic Transformation on Residual Stress in Resistance Spot Welded High-Strength Steel Sheets, Proceedings of the International Conference on Martensitic Transformations, Suita, Japan, No. PS-1-47 (2011).　

(71) S. Fujimoto, M. Mochizuki, Y. Morita, Y. Mikami, H. Tsuchiya and K. Nishimoto, Crystallographical Characterization of Initiation of Intergranular Stress Corrosion Cracking of Alloy 600 in PWR Environment, Proceedings of the 15th International Conference on Environmental Degradation of Materials in Nuclear Power Systems – Water Reactors, Colorado Springs, USA, No. M45497 (2011).　

(70) N. Ochi, S. Okano, M. Tanaka and M. Mochizuki, Computational Analysis of Heat Input Property during TIG Welding with Torch Tilt, 64th Annual Assembly of the International Institute of Welding, Chennai, India, IIW Doc. 212–1990–11 (2011).　

(69) Y. Mikami, K. Sogabe, S. Nishikawa, T. Sakai and M. Mochizuki, Anisotropic Mechanical Behavior of Ni-base Alloy Weld Metal Considering Crystal Orientation Distribution, Proceedings of the 11th International Conference on the Mechanical Behavior of Materials, Como, Italy, Vol. 10, pp. 1626-1631 (2011).　

(68) M. Mochizuki, S. Okano and N. Ochi, Near Net-Shape Adjustment in Welded Components by Optimization of Weld Sequence and Torch Configuration, Proceedings of the International Workshop on Thermal Forming and Welding Distortion, Bremen, Germany, pp. 333-340 (2011).　

(67) M. Mochizuki, Y. Mikami, S. Fujimoto, K. Nishimoto, Microscopic Stress Simulation by Multi-scale Analysis Considering Microstructure for SCC Evaluation of Repaired Weld Joints – Evaluation Technologies for Integrity in Repair Welding of Ageing Plants, and for Reliability of Repaired Welds (Part 3), Proceedings of the International Symposium on the Ageing Management and Maintenance of Nuclear Power Plants, Tokyo, Japan, pp. 230-239 (2011).　

(66) Y. Mikami, K. Sogabe, S. Nishikawa and M. Mochizuki, Multi-scale Analysis of Microscopic Stress Concentration at Grain Boundary in Weld Metal of Ni-based Alloy Joint for SCC Evaluation, Proceedings of the 18th European Conference on Fracture, Fracture of Materials and Structures from Micro to Macro Scale, B.04.6-4, Dresden, Germany (2010).　

(65) T. Hashimoto, Y. Osawa, S. Itoh, M. Kameyama, N. Hirano, N. Chigusa, K. Saida, M. Mochizuki and K. Nishimoto, Evaluation for Stability of Water Jet Peening during Long Term Operation, Proceedings of The 3rd Inter-University Research Seminar – IURS2010, Busan, Korea, pp. 51-54 (2010).　

(64) L. Yu, Y. Nakabayashi, M. N. B. Jaafar, M. Kameyama, S. Hirano, N. Chigusa, K. Saida, M. Mochizuki and K. Nishimoto, Prediction using Neural Network for Hardness in CGHAZ of Low-Alloy Steel Produced by Temper Bead Technique, Proceedings of The 3rd Inter-University Research Seminar – IURS2010, Busan, Korea, pp. 47-50 (2010).　

(63) M. Shibahara, E. Kawamura, T. Onda, S. Itoh, M. Mochizuki and K. Masaoka, Measurement of Three-dimensional Welding Deformation Using Digital Image Correlation Technique, Proceedings of the International Conference on Welding Science and Engineering, Shanghai, China, pp. 67-76 (2009).　

(62) R. Ihara, T. Hashimoto, M. Mochizuki and K. Nishimoto, Prediction of Residual Stress Distributions due to Surface Machining and Welding and Crack Growth Simulation, Proceedings of the International Conference on Welding Science and Engineering, Shanghai, China, pp. 51-58 (2009).　

(61) M. Mochizuki, Mis-Matching Effect of Weld-HAZ on Tensile Strength Limit in High Chromium Steel Welded Pipe-Joint for Sodium Cooled Fast Breeder Reactor, 12th International Conference on Pressure Vessel Technology, Jeju, Korea, No. M2B.6 (2009).

(60) T. Kawabata, H. Sakaibori, K. Ohnishi and M. Mochizuki, Mechanical Discussion on 950MPa Class Steel Plate, Welded Joint for Penstock, Report 2: Effect of Welding Conditions on Brittle Fracture Behavior and Fracture Assessment, Proceedings of the Conference on High Strength Steels for Hydropower Plants, Takasaki, Japan, pp. 14.1-8 (2009).

(59) M. Mochizuki, H. Kitano, S. Okano, T. Kawabata and H. Sakaibori, Mechanical Discussion on 950MPa Class Steel Plate, Welded Joint for Penstock, Report 1: Characteristics of Deformation and Strength by Numerical Welding Stress-Strain Simulation Considering Microstructural Effect, Proceedings of the Conference on High Strength Steels for Hydropower Plants, Takasaki, Japan, pp. 13.1-8 (2009).

(58) S. Okano, M. Mochizuki, K. Yamamoto and M. Tanaka, Approach to Link between Arc Physics and Weld Distortion through Heat Transport Phenomena, 62nd Annual Assembly of the International Institute of Welding, IIW Doc. 212-1154-09, Singapore (2009).

(57) N. Ochi, S. Okano, M. Mochizuki, J. Shimamura and N. Ishikawa, Computational Analysis of Temperature Distribution in Multiple-Electrode Submerged Arc Welding, Annual Assembly of the International Institute of Welding, IIW Doc. XII-1957-09, Singapore (2009).

(56) M. Mochizuki and T. Kurimura, Round Robin Tests of Weld Residual Stress using X-Ray Diffraction and Computational Simulation, 62nd Annual Assembly of the International Institute of Welding, IIW Doc. X-1661-09, XIII-2294-09, XV-1327-09, Singapore (2009).

(55) T. Satoh, Y. Mikami, M. Mochizuki, N. Suzuki and M. Toyoda, Effect of Geometric Imperfections and Mechanical Properties on Bending Capacity of High-Strength Linepipes, Proceedings of 8th International Symposium of the Japan Welding Society, Special Session: Pipeline Technology Now and Then, Kyoto, Japan, pp. 119-125 (2008).

(54) M. Mochizuki, Y. Mikami and S. Okano, Weld Microstructure and Distortion Controls by Considering Process Mechanics, 61st Annual Assembly of the International Institute of Welding, Graz, Austria, IIW Doc. X-1644-08 (2008).

(53) S. Okano, M. Mochizuki and M. Toyoda, Positional Condition Setting for Reduction of Weld Distortion by In-Process Control Welding, Proceedings of the 2007 International Forum on Welding Science and Engineering - The Design and Application on Green Welding Materials, Beijing, China (2007).

(52) M. Mochizuki, S. Okano, H. Shirai, Y. Hirata and M. Toyoda, Appropriate Molten Pool Configuration from a Viewpoint of Weld Distortion Control, 60th Annual Assembly of the International Institute of Welding, Dubrovnik-Cavtat, Croatia, IIW Doc. XII-1925-2007 (2007).

(51) S. Okano, M. Mochizuki and M. Toyoda, Temperature Distribution for Reduction of Angular Distortion by In-process Control Welding, 60th Annual Assembly of the International Institute of Welding, Dubrovnik-Cavtat, Croatia, IIW Doc. X-1619-2007 (2007).

(50) H. Shirai, M. Mochizuki and M. Toyoda, Reduction of Welding Deformation by Split Laser Beams in Automobile Parts, 60th Annual Assembly of the International Institute of Welding, Dubrovnik-Cavtat, Croatia, IIW Doc. X-1618-2007 (2007).

(49) M. Mochizuki, R. Higuchi, Y. Mikami and M. Toyoda, Evaluation of Heterogeneity of Microscopic Deformation and Stress Distribution in Steel and Its Weld by FEM-MD Coupling Simulation, 60th Annual Assembly of the International Institute of Welding, Dubrovnik-Cavtat, Croatia, IIW Doc. X-1617-2007 (2007).

(48) M. Mochizuki, H. Shirai and M. Toyoda, Microscopic Deformation Behavior of Small-Diameter Pipe by Laser Welding, Proceedings of the 5th German-Japan Seminar on Materials, Processes and Components, Fraunhofer Institute for Mechanics of Materials, Freiburg, Germany, No. S5-2 (2007).

(47) M. Mochizuki and K. Miyazaki, Effects of Equipped Conditions in Girth-Welded Pipes on Residual Stress Distribution and SCC Propagation, 59th Annual Assembly of the International Institute of Welding, Quebec, Canada, IIW Doc. X-1609-2006 (2006).

(46) M. Mochizuki, Y. Mikami, H. Yamasaki and M. Toyoda, Elastic Predicting Method of Weld Distortion of Large Structures Using Numerical Simulation Results by Thermal-Elastic-Plastic Analysis of Small Components, 59th Annual Assembly of the International Institute of Welding, Quebec, Canada, IIW Doc. X-1607-2006 (2006).

(45) R. Higuchi, M. Mochizuki and M. Toyoda, FEM-MD Combined Method for Investigation on Effects of Microscopic Heterogeneity near Weld Zone on Strength Characteristics, 59th Annual Assembly of the International Institute of Welding, Quebec, Canada, IIW Doc. X-1606-2006 (2006).

(44) M. Mochizuki, Micro-Macro Mechanics in Linepipe Steels and Welds, Proceedings of Asia Steel International Conference 2006, Fukuoka, Japan, pp. 264-269 (2006).

(43) Y. Nakashima, Y. Kumon, K. Inose, Y. Nakanishi, Y. Morikage, T. Kubo, K. Amano, Y. Mikami and M. Mochizuki, Welding Distortion Behavior of Steel Welds with Low-temperature Transformation Welding Wire, 58th Annual Assembly of the International Institute of Welding, Prague, Czech, IIW Doc. XV-1196-2005 (2005).

(42) M. Mochizuki and K. Miyazaki, SCC Propagation under Weld Residual Stress Fields with Different Boundary Conditions, 58th Annual Assembly of the International Institute of Welding, Prague, Czech, IIW Doc. X-1583-2005 (2005).

(41) Y. Mikami, Y. Morikage, M. Mochizuki and M. Toyoda, Evaluation of Relationship between Transformation Expansion of Weld Metal and Weld Distortion through Numerical Simulation Considering Phase Transformation Effect, 58th Annual Assembly of the International Institute of Welding, Prague, Czech, IIW Doc. X-1582-2005 (2005).

(40) J. Katsuyama, M. Mochizuki and M. Toyoda, Effect of Repair Welding on the Residual Stress Distribution at Piping Butt Welded Joint, 58th Annual Assembly of the International Institute of Welding, Prague, Czech, IIW Doc. X-1581-2005 (2005).

(39) M. Mochizuki, J. Katsuyama, R. Higuchi and M. Toyoda, Study of Residual Stress Distribution at Start-Finish Point of Circumferential Welding Studied by 3D-FEM Analysis, 58th Annual Assembly of the International Institute of Welding, Prague, Czech, IIW Doc. X-1580-2005 and IIW Doc. X-XIII-XV-111-05 (2005).

(38) J. Katsuyama, M. Mochizuki, R. Higuchi and M. Toyoda, Analytical Evaluation of Residual Stress and Work Hardening by Welding and Surface-Machining, Proceedings of the 4th German-Japanese Seminar on Materials, Processes and Components, Karlsruhe, Germany, No. 14 (2005).

(37) Y. Mikami, Y. Morikage, M. Mochizuki and M. Toyoda, Continuous Measurement and Three-dimensional FEM Simulation of Transient Distortion in Welded Joint with Low-temperature Transformation Welding Wire, Proceedings of the 4th German-Japanese Seminar on Materials, Processes and Components, Karlsruhe, Germany, No. 12 (2005).

(36) Y. Nakashima, Y. Kumon, K. Inose, Y. Nakanishi, Y. Morikage, T. Kubo, K. Amano, Y. Mikami, and M. Mochizuki, Welding Distortion Behavior of Steel Welds with Low-temperature Transformation Welding Wire, Proceedings of the 4th German-Japanese Seminar on Materials, Processes and Components, Karlsruhe, Germany, No. 11 (2005).

(35) H. Shirai, M. Urushizaki, M. Mochizuki and M. Toyoda, High Precision Welding Fabrication of Automotive Equipments, Proceedings of the Finnish-German-Japanese Joint International Seminar on Mechanical and Metallurgical Approaches to New Joining Process, Awaji-Island, Japan, pp. 82-89 (2004).

(34) M. Mochizuki, Y. Mikami, J. Katsuyama, R. Higuchi and M. Toyoda, Numerical Simulation of Weld Mechanics with Microstructural Effect, Proceedings of the Finnish-German-Japanese Joint International Seminar on Mechanical and Metallurgical Approaches to New Joining Process, Awaji-Island, Japan, pp. 60-69 (2004).

(33) M. Mochizuki, R. Higuchi, J. Katsuyama, M. Inuzuka, H. Nishida and M. Toyoda, Mechanical and Fracture Properties in Friction Stir Welded Joint of Aluminum Alloy Structures, Proceedings of the International Conference on Technical Trends and Future Prospectives of Welding Technology for Transportation, Land, Sea, Air and Space, Osaka, Japan, pp. 484-490 (2004).

(32) Y. Mikami, M. Mochizuki and M. Toyoda, Evaluation of Hardness and Microstructure in Welds Considering Weld Thermal Cycle and Phase Transformation, 57th Annual Assembly of the International Institute of Welding, Osaka, Japan, IIW Doc. X-1562-2004 (2004).

(31) M. Mochizuki and M. Toyoda, Residual Stress and Distortion by Pipeline Welding, Proceedings of the 4th International Conference on Pipeline Technology, Ostend, Belgium, Edited by R. Denys, Scientific Surveys Ltd, Beaconsfield, United Kingdom, ISBN 0-901360-34-1, Vol. 2, pp. 897-915 (2004).

(30) M. Mochizuki, Numerical Simulation of Microstructure and Residual Stress by Pipeline Welding, Proceedings of the International Conference on Pipeline Integrity and Repairs, Sydney, Australia, pp. 901-913 (2004).

(29) M. Mochizuki and M. Toyoda, Thermal and Residual Stresses due to Welding Heat Cycles Considering Phase Transformation Effect, Proceedings of the International Conference on Advanced Technology in Experimental Mechanics 2003, Nagoya, Japan, No. OS04W0422 (2003).

(28) M. Mochizuki, K. Miyazaki and M. Toyoda, Surface Crack Propagation Analysis under Residual Stress Field, 56th Annual Assembly of the International Institute of Welding, Bucharest, Romania, IIW Doc. X-1526-2003 (2003).

(27) H. Yamasaki, M. Mochizuki and M. Toyoda, Distortion Behavior during In-Process Control Welding by Additional Cooling, 56th Annual Assembly of the International Institute of Welding, Bucharest, Romania, IIW Doc. X-1525-2003 and IIW Doc. X/XIII/XV-RSDP-87-03 (2003).

(26) M. Mochizuki and M. Toyoda, Active In-Process Control of Welding Distortion, 56th Annual Assembly of the International Institute of Welding, Bucharest, Romania, IIW Doc. X-1524-2003 and IIW Doc. X/XIII/XV-RSDP-86-03 (2003).

(25) M. Mochizuki, H. Shirai and M. Toyoda, Microscopic Deformation Behavior under Laser Welding, 56th Annual Assembly of the International Institute of Welding, Bucharest, Romania, IIW Doc. X-1523-2003 and IIW Doc. X/XIII/XV-RSDP-85-03 (2003).

(24) M. Mochizuki, M. Toyoda, T. Kubo and Y. Morikage, Weld Metal with Property of Low-Temperature Phase Transformation for Improving Fatigue Strength by Residual Stress Reduction, 56th Annual Assembly of the International Institute of Welding, Bucharest, Romania, IIW Doc. X-1522-2003 (2003).

(23) M. Toyoda, M. Mochizuki, M. Inuzuka and H. Nishida, Fracture Toughness of Structural Aluminum Plate Joints by Friction Stir Welding, 56th Annual Assembly of the International Institute of Welding, Bucharest, Romania, IIW Doc. X-1521-2003 (2003).

(22) M. Mochizuki and M. Toyoda, Numerical Simulation of Temperature and Microstructure in X-80 Girth Welded Pipelines, Proceedings of the International Conference on Application and Evaluation of High-Grade Linepipes in Hostile Environments, Yokohama, Japan, Edited by R. Denys and M. Toyoda, Scientific Surveys Ltd, Beaconsfield, United Kingdom, ISBN 0-901360-31-7, pp. 841-863 (2002).

(21) C. S. Ro, T. Yamada, M. Mochizuki, N. Ishikawa, H. S. Bang and M. Toyoda, Fracture Toughness in High Energy Density Beam Welded Joints of High Tensile Steels, Proceedings of the International Welding and Joining Conference in Korea 2002, Gyeongju, South Korea, No. WM1-4, pp. 1-7 (2002).

(20) H. Shirai, S. Sawamoto, T. Sato, M. Toyoda and M. Mochizuki, Analysis of Deformation Behavior of Pipe under Laser Welding, Proceedings of the 21st International Congress on Applications of Lasers and Electro-Optics, Scottsdale, Arizona, USA, No. LMC-A-3, pp. 1-8 (2002).

(19) M. Toyoda, M. Mochizuki, T. Shintomi and Y. Hashimoto, Analytical Study on Deformation and Strength in HAZ-Softened Weld Joints of Fine-Grained Steels, 55th Annual Assembly of the International Institute of Welding, Copenhagen, Denmark, IIW Doc. X-1503-2002 (2002).

(18) M. Toyoda, M. Mochizuki, S. Matsushima, T. Kubo and Y. Morikage, Residual Stress Reduction by Using Weld Metal with Property of Low-Temperature Phase Transformation, 55th Annual Assembly of the International Institute of Welding, Copenhagen, Denmark, IIW Doc. X-1502-2002 (2002).

(17) M. Toyoda, M. Mochizuki and S. Matsushima, Analytical Study on Residual Stress and Microstructures by Repair Welds, 55th Annual Assembly of the International Institute of Welding, Copenhagen, Denmark, IIW Doc. X-1501-2002 (2002).

(16) M. Toyoda, M. Mochizuki, S. Matsushima, Z. Zhang, O. Gundersen and C. Thaulow, Behavior of Phase Transformation and Thermal Stress during Welding Heat Cycles, 55th Annual Assembly of the International Institute of Welding, Copenhagen, Denmark, IIW Doc. X-1500-2002 (2002).

(15) Y. Mikami, M. Mochizuki and M. Toyoda, Effect of Inter-Pass Temperature on Distribution of Microstructure and Mechanical Properties in Multi-Layered Welded Joints, 55th Annual Assembly of the International Institute of Welding, Copenhagen, Denmark, IIW Doc. X-1499-2002 (2002).

(14) M. Toyoda, M. Mochizuki, M. Ohata, T. Yamada and N. Ishikawa, Fracture Path and Toughness in High-Energy Beam Welded Joints of High Strength Steels, 55th Annual Assembly of the International Institute of Welding, Copenhagen, Denmark, IIW Doc. X-1498-2002 (2002).

(13) M. Mochizuki and M. Toyoda, Control and Reduction of Residual Stress in Welded Structures, Proceedings of the 2nd German-Japanese Seminar on Simulation of Materials, Processes and Components, Freiburg, Germany, No. C-5, pp. 1-19 (2002).

(12) M. Mochizuki and M. Toyoda, Weld Simulation of Temperature, Microstructure, and Stress-Strain Behaviors, Proceedings of the 2nd German-Japanese Seminar on Simulation of Materials, Processes and Components, Freiburg, Germany, No. P-1, pp. 1-9 (2002).

(11) M. Mochizuki, M. Toyoda, W. Burget and P. Pasquale, Effects of Welding Heat Cycles on Strength and Toughness in Beam-to-Column Connections of Steel Framed Structures, Proceedings of the 7th International Welding Symposium of Japan Welding Society, Kobe, Japan, Vol. 2, pp. 1153-1158 (2001).

(10) M. Mochizuki, G. B. An and M. Toyoda, Prediction of Ductile-to-Brittle Transition in Welded Joints with Strength Heterogeneity Subjected to Dynamic Loading, Proceedings of the Asian Pacific Conference on Fracture and Strength '01 and the International Conference on Advanced Technology in Experimental Mechanics '01, Sendai, Japan, Vol. 1, pp. 146-151 (2001).

(9) M. Toyoda and M. Mochizuki, Three-Dimensional Computer Simulation of Moving Heat Source with Phase Transformation and Residual Stress in Multi-Pass Welded Joints, Proceedings of the 2nd Joint Slovenian-Japanese Seminar on Welding Fracture Mechanics and Dynamic Loading, Bohinj, Slovenia, No. 10, pp. 1-10 (2001).

(8) M. Toyoda and M. Mochizuki, Numerical Simulation of Mechanical Properties in Beam-to-Column Welded Connections of Steel Framed Structures, 1st Sub-Commission XF Meeting of IIW Commission X, Cambridge, United Kingdom, IIW Doc. XF-008-2001 (2001).

(7) W. Burget, P. Pasquale and M. Mochizuki, Numerical Calculation of Residual Stresses for Cladded Plates, Proceedings of the 8th Japanese-German Joint Seminar on Structural Integrity and NDE in Power Engineering, Tokyo, Japan, pp. 452-463 (2001).

(6) M. Toyoda, M. Mochizuki, M. Kohara, Y. Hagiwara and H. Shimanuki, Crack Generation and Propagation in Ferrite/Martensite Dual-Phase Steels with Microscopic Heterogeneity, 53rd Annual Assembly of the International Institute of Welding, Florence, Italy, IIW Doc. X-1460-2000 and IIW Doc. SC X-F-091-00 (2000).

(5) M. Toyoda, M. Mochizuki, G. B. An and T. Ohmura, Characteristics of Strength and Fracture in Undermatched Welded Joints by Dynamic Loading, 53rd Annual Assembly of the International Institute of Welding, Florence, Italy, IIW Doc. X-1459-2000 and IIW Doc. SC X-F-090-00 (2000).

(4) M. Toyoda, M. Mochizuki, T. Ohmura and G. B. An, Temperature Rise by Plastic Deformation under Dynamic Loading in Structural Steels and Their Undermatched Joints, Proceedings of the International Seminar on Numerical Analysis of Solid and Fluid Dynamics in 1999, Suita, Japan, pp. 217-224 (1999).

(3) M. Mochizuki, Residual Stress in Primary Piping of Girth Welded Joint, Proceedings of the Post Conference Seminar at the 13th International Conference on Structural Mechanics in Reactor Technology, Assuring Structural Integrity of Steel Reactor Pressure Boundary Components, Iguazu, Argentina, No. S4.2, pp. 1-9 (1995).

(2) M. Mochizuki, K. Enomoto, S. Sakata, K. Kurosawa, H. Saito, H. Tsujimura and K. Ichie, A Study on Residual Stress Improvement by Water Jet Peening, Proceedings of the 5th International Conference on Shot Peening, Oxford, United Kingdom, pp. 247-256 (1993).

(1) M. Mochizuki, K. Enomoto, N. Okamoto, H. Saito and E. Hayashi, Welding Residual Stresses for a Pipe Penetrating a Thick Plate, Proceedings of the Post Conference Seminar at the 11th International Conference on Structural Mechanics in Reactor Technology, Assuring Structural Integrity of Steel Reactor Pressure Boundary Components, Taipei, Taiwan, Republic of China, No. 3-10-1, pp. 1-9 (1991).

2.3 Proceedings of Domestic Conference in Japan

(62) A. Ikezaki, S. Okano and M. Mochizuki, A Discussion about Distribution of Temperature and Inherent Strain Dominating Weld Distortion, Proceedings of the 2011 National Symposium on Welding Mechanics and Design (in Japanese), Japan Welding Society, Suita, Japan, pp. 523-530 (2011).　

(61) S. Itoh, M. Shibahara and M. Mochizuki, Prediction of Welding Distortion of Formed Head Attached Pipes in Two-Phase Flow Separator, Proceedings of the 2011 National Symposium on Welding Mechanics and Design (in Japanese), Japan Welding Society, Suita, Japan, pp. 349-352 (2011).　

(60) M. Hata, M. Mochizuki, S. Itoh, M. Shibahara and Y. Yamashita, Inherent Strain Analysis of Large-Scale Ship Assemblies Using Idealized Explicit Method, Proceedings of the 2011 National Symposium on Welding Mechanics and Design (in Japanese), Japan Welding Society, Suita, Japan, pp. 329-336 (2011).　

(59) A. Kawaguchi, S. Itoh, S. Okano, T. Hashimoto and M. Mochizuki, Measurement and Numerical Simulation of Residual Stress for Repair Welding of Thick Pipe, Proceedings of the 2011 National Symposium on Welding Mechanics and Design (in Japanese), Japan Welding Society, Suita, Japan, pp. 131-134 (2011).　

(58) Y. Tanabe, K. Mitani, A. Hatanaka, M. Iyota, S. Okano and M. Mochizuki, Investigation of Method for Estimating Stress-Strain Curve Using Instrumented Indentation Technique, Proceedings of 2011 Fall Meeting of Japan Society of Non-Destructive Inspection (in Japanese), Awaji-Yumebutai, Ｊａｐａｎ (2011).　

(57) M. Iyota, T. Hashimoto, Y. Mikami, K. Taniguchi, R. Ikeda and M. Mochizuki, Highly Precise Evaluation of the Residual Stress in Resistance Spot Welds by the X-ray Diffraction Method and Inspection by the Numerical Simulation, Proceedings of 2011 Stress-Strain Evaluation Division Meeting of Japan Society of Non-Destructive Inspection (in Japanese), Nagoya, Japan, No. SSE-0001 (2011).　

(56) S. Fujimoto, H. Morita, H. Tsuchiya, M. Mochizuki and Y. Mikami, Relation among Initiation of IGSCC, Microstructure, and Microscopic Stress Distribution in Simulated Primary PWR Environments, Zairyo-to-Kankyo (in Japanese), Japan Society of Corrosion Engineering, Nagoya, Japan, Vol. 58, No. F11078 (2011).　

(55) T. Hashimoto, Y. Osawa, S. Itoh, M. Kameyama, S. Hirano, N. Chigusa, K. Saida, M. Mochizuki and K. Nishimoto, Long-Term Stability Considering Superposition of Construction Processes for Residual Stress Improvement by Water Jet Peening, Proceeding of the 45th Symposium on X-Ray Studies on Mechanical Behaviour of Materials (in Japanese), Tokyo, Japan (2011).　

(54) S. Nishikawa, K. Sogabe, T. Hashimoto, Y. Mikami, A. Yamaguchi and M. Mochizuki, Study on Microscopic Residual Stress Evaluation near Boundary between Nickel Based Alloy Weld Metal and Low Alloy Steel, Zairyo-to-Kankyo (in Japanese), Japan Society of Corrosion Engineering, Naha, Japan, No. F10A110 (2010).　

(53) T. Hashimoto, Y. Osawa, S. Itoh, K. Saida, M. Mochizuki, K. Nishimoto, M. Kameyama, S. Hirano and N. Chigusa, Effect of Residual Stress Degreasing by Water Jet Peening on Weld of Ni Based Alloy and Evaluation for Long Term Stability Under High Temperature Environment, Proceedings of the 50th Anniversary Symposium of Welding Metallurgy Committee of Japan Welding Society, Suita, Japan, pp. 111-114 (2010).　

(52) L. Yu, Y. Nakabayashi, K. Saida, M. Mochizuki, K. Nishimoto, M. Kameyama, S. Hirano and N. Chigusa, Quantitative Consideration for the Tempering Effect during Multi-pass Thermal Cycle in HAZ of Low-Alloy Steel, Proceedings of the 50th Anniversary Symposium of Welding Metallurgy Committee of Japan Welding Society, Suita, Japan, pp. 107-110 (2010).　

(51) R. Ihara, T. Hashimoto, Y. Mikami, J. Katsuyama, K. Onizawa and M. Mochizuki, Evaluation of Residual Stress Distribution due to Welding and Surface Machining and Crack Growth Behavior, Proceedings of the 7th Annual Assembly of Japan Society of Maintenology (in Japanese), Omae-zaki, Japan, pp. 611-616 (2010).　

(50) S. Nishikawa, S. Ohkita, A. Yamaguchi, K. Sogabe, Y. Mikami and M. Mochizuki, Effects of C and Nb Contents on Stress Corrosion Cracking of Shielded Metal Arc Weld Metal for 600 Type Alloy in High Temperature Pressurized Pure Water, Proceedings of the 7th Annual Assembly of Japan Society of Maintenology (in Japanese), Omae-zaki, Japan, pp. 550-555 (2010).　

(49) M. Mochizuki, T. Hashimoto and S. Okano, Measurement of X-ray Residual Stress and It’s Numerical Simulation in Welded Joints, Proceeding of the 45th Symposium on X-Ray Studies on Mechanical Behaviour of Materials (in Japanese), Kyoto, Japan, pp. 136-141 (2010).　

(48) T. Hashimoto, M. Mochizuki and K. Nishimoto, X-Ray Residual Stress Measurement in Weld of Ni Based Alloy by Using Two Dimensional Detector, Proceeding of the 45th Symposium on X-Ray Studies on Mechanical Behaviour of Materials (in Japanese), Kyoto, Japan, pp. 131-135 (2010).　

(47) K. Sogabe, Y. Mikami, S. Nishikawa and M. Mochizuki, Numerical Analysis of Microscopic Stress Distribution in Ni-base Alloy Weld Metal of CBB test, Proceedings of the 2009 National Symposium on Welding Mechanics and Design (in Japanese), Japan Welding Society, Suita, Japan, Japan, Vol. 2, pp. 665-672 (2009).　

(46) Y. Mikami, N. Kubota, H. Inoue, T. Kasuya, M. Mochizuki and K. Hiraoka, Effect of Specimen Geometry on Residual Stress Distribution in Cold Cracking Test Welds, Proceedings of the 2009 National Symposium on Welding Mechanics and Design (in Japanese), Japan Welding Society, Suita, Japan, Vol. 2, pp. 651-658 (2009).　

(45) A. Inao, Y. Mikami, H. Shimanuki and M. Mochizuki, Measurement of the Change of Microscopic Residual Stress and Strain Conditions in Ferrite-Martensite Lamellar Steels with Pre-Strain, Proceedings of the 2009 National Symposium on Welding Mechanics and Design (in Japanese), Japan Welding Society, Suita, Japan, Vol. 2, pp. 425-428 (2009).　

(44) R. Ihara, J. Katsuyama. K. Onizawa, T. Hashimoto, Y. Mikami and M. Mochizuki, Numerical Simulation of Residual Stress Distribution Generated by Machining and The Effect on Crack Growth, Proceedings of the 2009 National Symposium on Welding Mechanics and Design (in Japanese), Japan Welding Society, Suita, Japan, Vol. 2, pp. 393-396 (2009).　

(43) K. Onishi, T. Kawabata, H. Sakaibori, H. Kitano, S. Okano and M. Mochizuki, Mechanical Discussion on 950MPa Class Steel Plate Welded Joint for Penstock - Report 2: Effect of Welding Conditions on Brittle Fracture Behavior and Fracture Assessment, Proceedings of the 2009 National Symposium on Welding Mechanics and Design (in Japanese), Japan Welding Society, Suita, Japan, Vol. 2, pp. 343-350 (2009).　

(42) H. Kitano, S. Okano, M. Mochizuki, K. Onishi, T. Kawabata and H. Sakaibori, Mechanical Discussion on 950MPa Class Steel Plate Welded Joint – Report 1: Characteristics of Deformation and Strength by Numerical Welding Stress-Strain Simulation Considering Microstructural Effect, Proceedings of the 2009 National Symposium on Welding Mechanics and Design (in Japanese), Japan Welding Society, Suita, Vol. 2, Japan, pp. 335-342 (2009).　

(41) H. Kitano, S. Okano and M. Mochizuki, Effect of Strength Mismatch on Bending Strength and Deformation Behavior, Proceedings of the 2009 National Symposium on Welding Mechanics and Design (in Japanese), Japan Welding Society, Suita, Vol. 1, Japan, pp. 233-236 (2009).　

(40) K. Nakamoto, S. Okano, T. Hashimoto and M. Mochizuki, Experimental Examination on Influence of Torch Position on Weld Penetration and Distortion, Proceedings of the 2009 National Symposium on Welding Mechanics and Design (in Japanese), Japan Welding Society, Suita, Japan, Vol. 1, pp. 181-184 (2009).　

(39) Y. Kamitani, M. Shibahara, E. Kawamura, S. Itoh, M. Mochizuki and K. Masaoka, Development of Three Dimensional Welding Deformation Measurement Using Stereo Imaging Technique, Proceedings of the 2009 National Symposium on Welding Mechanics and Design (in Japanese), Japan Welding Society, Suita, Japan, Vol. 1, pp. 165-172 (2009).　

(38) J. Yamada, S. Okano, H. Mori and M. Mochizuki, Study on Effect of Penetration on Weld Distortion and Residual Stress, Proceedings of the 2009 National Symposium on Welding Mechanics and Design (in Japanese), Japan Welding Society, Suita, Vol. 1, Japan, pp. 133-136 (2009).　

(37) S. Itoh, T. Hashimoto, M. Kameyama and M. Mochizuki, Effects of PWHT on Residual Stress Distribution under Dissimilar Joint, Proceedings of the 2009 National Symposium on Welding Mechanics and Design (in Japanese), Japan Welding Society, Suita, Vol. 1, Japan, pp. 125-128 (2009).　

(36) M. Iyota, Y. Mikami, K. Taniguchi, R. Ikeda and M. Mochizuki, Numerical Simulation of Heat Transfer and Residual Stress of High-strength Steel Spot Welds, Proceedings of the 2009 National Symposium on Welding Mechanics and Design (in Japanese), Japan Welding Society, Suita, Japan, Vol. 1, pp. 113-118 (2009).　

(35) M. Mochizuki, Y. Mikami, S. Okano and S. Itoh, Innovative Computational Simulation of Weld Residual Stress from Mega- to Micro-Structures, Proceedings of the 6th Annual Assembly of Japan Society of Maintenology (in Japanese), Sendai, Japan, pp. 452-457 (2009).

(34) K. Mitani, M. Mochizuki and M. Toyoda, Hybrid Inspection of Thickness and Stress Conditions in Piping, Proceedings of Joint Meeting on Inspection, Evaluation and Maintenance, (in Japanese), Tokyo, Japan, pp. 45-48 (2008).

(33) H. Mori, J. Katsuyama, M. Mochizuki and K. Nishimoto, Effect of Residual Stress and Hardening on Grain Boundary Sliding in Welds of Low-Carbon Stainless Steels with Surface Machining, Proceedings of the 4th Annual Assembly of Japan Society of Maintenology (in Japanese), Fukui, Japan, pp. 141-144 (2007).

(32) W. Asano, J. Katsuyama, M. Mochizuki and M. Toyoda, Evaluation of Mechanical Property by Weld and Surface-Machining for Butt Joints of Austenite Stainless Steel Pipes, Proceedings of the 2006 National Symposium on Welding Mechanics and Design (in Japanese), Japan Welding Society, Suita, Japan, Vol. 2, pp. 757-760 (2006).

(31) R. Higuchi, M. Mochizuki and M. Toyoda, Proposal of Predicting Method for Stress-Strain Relationship in Microstructural Region Using Triangular Pyramidal Indenter, Proceedings of the 2006 National Symposium on Welding Mechanics and Design (in Japanese), Japan Welding Society, Suita, Japan, Vol. 2, pp. 647-650 (2006).

(30) N. Harada, R. Higuchi, M. Mochizuki and M. Toyoda, Microscopic Stress Analysis of Steels Concerning Heterogeneity of Grain Shape and Non-Uniform Deformation near Grain Boundary, Proceedings of the 2006 National Symposium on Welding Mechanics and Design (in Japanese), Japan Welding Society, Suita, Japan, Vol. 2, pp. 597-600 (2006).

(29) R. Higuchi, S. Shinike, M. Mochizuki and M. Toyoda, Evaluation of Stress Distribution Considering Microscopic Heterogeneity Affected by Thermal History near Weld Zone Using FEM-MD Combined Method, Proceedings of the 2006 National Symposium on Welding Mechanics and Design (in Japanese), Japan Welding Society, Suita, Japan, Vol. 2, pp. 593-596 (2006).

(28) S. Okano, M. Mochizuki and M. Toyoda and T. Ueyama, In-process Control Welding for Welding Distortion by Rear Cooling, Proceedings of the 2006 National Symposium on Welding Mechanics and Design (in Japanese), Japan Welding Society, Suita, Japan, Vol. 2, pp. 563-568 (2006).

(27) K. Amano, K. Yasuda, T. Kubo, Y. Morikage, Y. C. Kim, M. Mochizuki, K. Inose and Y. Nakashima, Reduction of Weld Distortion by Low Phase Transformation Welding Materials, Proceedings of the 2006 National Symposium on Welding Mechanics and Design (in Japanese), Japan Welding Society, Suita, Japan, Vol. 2, pp. 537-545 (2006).

(26) H. Iwahashi, T. Nakamura, M. Mochizuki, K. Hiraoka and M. Toyoda, Fundamental Study on Strength of Welded Structure of High Strength Steels with Softened Region in Heat-Affected Zone, Proceedings of the 2006 National Symposium on Welding Mechanics and Design (in Japanese), Japan Welding Society, Suita, Japan, Vol. 1, pp. 203-206 (2006).

(25) A. Tsumaya, K. Inoue, M. Mochizuki, H. Wakamatsu and E. Arai, Basic Study of the Plant Maintenance Model Considering Plant Improvement/Modification, Proceedings of the 3rd Annual Assembly of Japan Society of Maintenology (in Japanese), Sendai, Japan, pp. 36-41 (2006).

(24) M. Mochizuki, Y. Mikami, J. Katsuyama and M. Toyoda, Reduction of Fabricating Distortion and Improvement of Operating Fatigue Strength by Controlling Transformation Temperature of Weld Metal, Proceeding of the 10th Symposium on Strength Design and Safety Evaluation of Machinery and Structures (in Japanese), Society of Materials Science of Japan, Kyoto, Japan, pp. 25-28 (2006).

(23) M. Mochizuki, H. Yamasaki, Y. Mikami and M. Toyoda, Analytical Study on Effects of Strain Distribution in Welding Start/End on Welding Distortion, Proceedings of the 2004 National Symposium on Welding Mechanics and Design (in Japanese), Japan Welding Society, Suita, Japan, pp. 411-414 (2004).

(22) Y. Mikami, M. Mochizuki, M. Toyoda, Y. Hashiba, T. Hasegawa and S. Ohkita, Evaluation of Hardness Distribution of Multipass Weld Metal with Numerical Simulation of Weld Thermal Cycles and Phase Fraction of Microstructure, Proceedings of the 2004 National Symposium on Welding Mechanics and Design (in Japanese), Japan Welding Society, Suita, Japan, pp. 211-218 (2004).

(21) M. Mochizuki, Y. Mikami, M. Toyoda, T. Nakamura and K. Hiraoka, Numerical Simulation of Hardness Distribution in Welds with Ultra-Narrow Gap Welding, Proceedings of the 2004 National Symposium on Welding Mechanics and Design (in Japanese), Japan Welding Society, Suita, Japan, pp. 203-210 (2004).

(20) J. Katsuyama, M. Yoneda, R. Higuchi, M. Mochizuki and M. Toyoda, Mechanical Property Evaluation near the Welding Joint of Low Carbon Stainless Steel by 2D- and 3D-FEM, Proceedings of the 2004 National Symposium on Welding Mechanics and Design (in Japanese), Japan Welding Society, Suita, Japan, pp. 93-96 (2004).

(19) N. Konda, K. Arimochi, Y. Matsukawa, M. Hirono, H. Arima, Y. Morishita, O. Yasuda, M. Mochizuki and M. Toyoda, Improvement of Fatigue Strength at Beam to Column Connections by Application of Newly Developed Steels with Superior Resistance against Fatigue Crack Growth, Proceedings of the 2004 National Symposium on Welding Mechanics and Design (in Japanese), Japan Welding Society, Suita, Japan, pp. 35-38 (2004).

(18) H. Shirai, M. Urushizaki, S. Sawamoto, M. Mochizuki and M. Toyoda, Distortion Behavior of Automotive Parts by Laser Welding, Reduction of Distortion by Multiple Heat Input, Transactions of Japan Laser Processing Society (in Japanese), Vol. 59, pp. 8-13 (2003).

(17) T. Hase, T. Tada, H. Nishida, M. Inuzuka, M. Mochizuki and M. Toyoda, Ductile Crack Propagation Resistance and Fracture Toughness of Thick Plate FSW Joint, Proceedings of the 2002 National Symposium on Welding Mechanics and Design (in Japanese), Japan Welding Society, Suita, Japan, pp. 435-438 (2002).

(16) M. Mochizuki, T. Tada, S. Matsushima and M. Toyoda, Effects of Welding Conditions on Residual Stress and Microstructures by Repair Welds, Proceedings of the 2002 National Symposium on Welding Mechanics and Design (in English), Japan Welding Society, Suita, Japan, pp. 395-402 (2002).

(15) M. Mochizuki, S. Matsushima, Y. Morikage, T. Kubo and M. Toyoda, Residual Stress in a Box Welded Joint between Flange and Stiffener by Using Weld Metal with Property of Low-Temperature Phase Transformation, Proceedings of the 2002 National Symposium on Welding Mechanics and Design (in English), Japan Welding Society, Suita, Japan, pp. 387-394 (2002).

(14) M. Mochizuki, S. Matsushima, Y. Morikage, T. Kubo and M. Toyoda, Analytical and Experimental Studies on Residual Stress Reduction by Using Phase Transformation of Weld Metal, Proceedings of the 2002 National Symposium on Welding Mechanics and Design (in English), Japan Welding Society, Suita, Japan, pp. 379-386 (2002).

(13) T. Handa, T. Kubo, M. Ohata, M. Mochizuki, Y. Maeda and M. Toyoda, Effect of Mechanical Properties of Steels on Ductile to Brittle Transition Temperature - Study on Correlation between Charpy and CTOD Transition Temperatures, Proceedings of the 2002 National Symposium on Welding Mechanics and Design (in Japanese), Japan Welding Society, Suita, Japan, pp. 318-321 (2002).

(12) T. Kawabata, K. Arimochi, M. Ohata, M. Mochizuki and M. Toyoda, Investigation on Enhancement of Uniform Elongation in 780MPa Class High Tensile Strength Steel Plate, Proceedings of the 2002 National Symposium on Welding Mechanics and Design (in Japanese), Japan Welding Society, Suita, Japan, pp. 311-317 (2002).

(11) T. Yamada, T. Aono, N. Ishikawa, M. Ohata, M. Mochizuki, and M. Toyoda, Fracture Toughness of High Power Beam Welds for High Strength Steel, Proceedings of the 2002 National Symposium on Welding Mechanics and Design (in Japanese), Japan Welding Society, Suita, Japan, pp. 227-230 (2002).

(10) H. Yoshida, E. Kurosawa, M. Mochizuki and M. Toyoda, Reduction of Distortion Caused by Circumferential Welding of Thin-Cylindrical Components with Four-Torch Welding, Proceedings of the 2002 National Symposium on Welding Mechanics and Design (in Japanese), Japan Welding Society, Suita, Japan, pp. 129-136 (2002).

(9) H. Shirai, M. Urushizaki, S. Sawamoto, M. Mochizuki and M. Toyoda, Minimization of Deformation by Tightly Focused Laser Beam at High Speed - Study of Deformation Behavior by Laser Welding in Micron or Sub-Micron Area in Automobile Parts (Report 2), Proceedings of the 2002 National Symposium on Welding Mechanics and Design (in Japanese), Japan Welding Society, Suita, Japan, pp. 123-128 (2002).

(8) H. Shirai, M. Urushizaki, S. Sawamoto, M. Mochizuki and M. Toyoda, Analysis of Bending Deformation Behavior in Cylindrical Parts - Study of Deformation Behavior by Laser Welding in Micron or Sub-Micron Area in Automobile Parts (Report 1), Proceedings of the 2002 National Symposium on Welding Mechanics and Design (in Japanese), Japan Welding Society, Suita, Japan, pp. 115-122 (2002).

(7) M. Mochizuki, Y. Oki, H. Yamasaki, N. Takahashi and M. Toyoda, Fundamental Study on Active In-Process Control of Welding Distortion, Proceedings of the 2002 National Symposium on Welding Mechanics and Design (in English), Japan Welding Society, Suita, Japan, pp. 107-114 (2002).

(6) Y. Mikami, M. Mochizuki and M. Toyoda, Effect of Welding Pass Sequence on Microstructure and Hardness in Multi-Layered Welded Joints of Beam-to-Column Connections of Steel Framed Structures, Proceedings of the 2002 National Symposium on Welding Mechanics and Design (in Japanese), Japan Welding Society, Suita, Japan, pp. 51-56 (2002).

(5) M. Mochizuki, M. Kohara, S. Yoshida, M. Ohata and M. Toyoda, Microcrack Generation Behavior and Characteristics of Stress and Strain Distribution in Structural Steel with Microscopic Heterogeneity, Proceedings of the '99 National Symposium on Welding Mechanics and Design (in Japanese), Japan Welding Society, Suita, Japan, pp. 99-106 (1999).

(4) T. Nishio, H. Nakagawa, M. Mochizuki, T. Naruse, K. Shinmei and K. Niikura, Reliability Evaluation in Welded Runner of Pump-Turbine, Proceedings of the 25th Memorial Conference of the Japan Turbomachinery Institute (in Japanese), Sapporo, Japan, Vol. 41, pp. 93-98 (1998).

(3) S. Okido, M. Mochizuki, M. Hayashi, Y. Morii, N. Minakawa and Y. Tsuchiya, Residual Stress Measurement by Neutron Diffraction, Proceedings of the 29th Symposium on Stress-Strain Measurement and Strength Evaluation (in Japanese), Tokyo, Japan, pp. 146-151, pp. 146-151 (1998).

(2) K. Enomoto, K. Hirano, M. Mochizuki, K. Kurosawa, H. Saito and E. Hayashi, Improvement of Residual Stress on Material Surface by Water Jet Peening, Proceedings of the Symposium for Material Strength Using X-Rays (in Japanese), Kyoto, Japan, Vol. 31, pp. 152-157 (1995).

(1) M. Mochizuki, N. Saito, S. Sakata and K. Moriguchi, Residual Stress Analysis Traced Welding Pass Sequence Using Inherent Strain, Proceedings of the JSASS/JSME Structures Conference (in Japanese), Japan Society for Aeronautical and Space Sciences and Japan Society of Mechanical Engineers, Vol. 35, Kyoto, Japan, pp. 114-117 (1993).

3. Publication Books

(4) M. Mochizuki, Minimizing Angular Distortion in Welding by Reverse-Side Heating, Minimization of Welding Distortion and Buckling: Modeling and Implementation, P. Michaleris, Ed., Woodhead Publishing Limited, Cambridge, United Kingdom, pp. 273-288 (2011).　

(3) M. Toyoda and M. Mochizuki, Mechanics and Design of Welded Structures, Special Lectures for Welding and Joining Technology (in Japanese), Edited by Japan Welding Society, Chapter 3, Sanpo Publishing, Co. Ltd., ISBN4-88318-134-0, pp. 211-288 (2005).

(2) Japan Welding Society, Edited, Strength Characteristics by Weld HAZ Undermatching in High Tensile Steels (in Japanese), Ad-Hoc Databook, No. 2, All Manuscript Written by M. Mochizuki, Japan Welding Society (2004).

(1) M. Mochizuki, Analytical Study on Effect of Welding Multiple Heat Cycles on Joint Performances, Control Method of Heat Input and Interpass Temperature in Steel Framed Structures (in Japanese), Edited by T. Nakagomi, Chapter 5, Committee of Welding of Steel Framed Structures, Japan Welding Society, pp. 97-111 (2002).

4. Lecture Papers, Review Papers and Topics, etc.

4.1 Lecture Papers and Review Papers (Not included Invited Lectures)

(51) M. Mochizuki, M. Tanaka and F. Miyasaka, Simulation Model Integration for TIG and MIG Welding, Welding Technology (in Japanese), Vol. 60, No. 2, pp. 76-84 (2012).　

(50) M. Mochizuki, Welding Simulation in Heavy Industries, Proceedings of the PUCA ESI Users’ Forum, Tokyo, Japan, No. EH-09 (2011).　

(49) K. Yasuda, H. Inoue, K. Wang, M. Mochizuki, Y. Mikami, K. Nishio, T. Koseki and Y. Sato, Trend of Welding & Joining in Japan - Welding Metallurgy of Steels, Journal of the Japan Welding Society (in Japanese), Vol. 80, No. 5, pp. 414-417 (2011).

(48) M. Mochizuki, Effects of Welds on Deformation, Strength, and Aseismic Performance, Textbook for the 14th Forum on Welding and Joining (in Japanese), Shikoku Industry and Technology Promotion Center, Tokushima, Japan, pp. 1-26 (2011).　

(47) M. Mochizuki, Ultra-Large Scale Simulation of Weld Distortion of Ship Block by Using Solid Element in FEM, Textbook for KSSG Symposium of Japan Society of Naval Architects and Offshore Engineering (in Japanese), pp. 15-34 (2011).　

(46) M. Mochizuki, Computer Simulation of Welding for Materials Performances, Design, Fabrication, and Maintenance, Textbook for Trends of Computer Simulation in Nuclear Power Plants, Committee of Nuclear Technology of Japan Welding Engineering Society (2011).　

(45) M. Mochizuki, Methodology Development for Adaptive Design and Fabrication in High Chromium Steel Welded Pipe-Joint for Sodium Cooled Fast Breeder Reactor, Proceedings of Annual Symposium for FY2010 on Innovative Nuclear Research and Development Program (in Japanese), Ministry of Education, Culture, Sports, Science and Technology of Japan, No. 070303 (2011).

(44) M. Mochizuki and Y. Mikami, Residual Stress Simulation for Preventing Crack during Weld Process in High Tensile Strength Steels, Proceedings of the ESI Users’ Forum, Tokyo, Japan, No. W&C-4 (2010).　

(43) M. Mochizuki, Welding Mechanics: Part I-1 - Fundamentals of Material Strength and Deformation, Textbook of 2010's Special Summer Lecture on Welding Engineering (in Japanese), Japan Welding Society, Osaka, Japan, pp. 19-36 (2010).　

(42) M. Shibahara, S. Itoh and M. Mochizuki, Precise Measurement of Weld Distortion by Three-Dimensional Stereo Imaging Technique, Pre-prints of National Meeting of Japan Welding Society (in Japanese), Vol. 86, pp. S24-S29 (2010).　

(41) M. Mochizuki, Methodology Development for Adaptive Design and Fabrication in High Chromium Steel Welded Pipe-Joint for Sodium Cooled Fast Breeder Reactor, Proceedings of Annual Symposium for FY2009 on Innovative Nuclear Research and Development Program (in Japanese), Ministry of Education, Culture, Sports, Science and Technology of Japan, No. 070303 (2010).

(40) M. Mochizuki, Dreams for New Welding Technology in Next Generation by Using Process Mechanics, Welding Technology, Vol. 58, No. 1, pp. 76-84 (2010).　

(39) M. Mochizuki, Recent Evaluation Methods for Thermal Process Sustaining Fundamental Technology and Engineering – Towards Process Mechanics, Proceedings of the 136th Future Mechanical Process Committee of Japan Society for Promotion of Science, Vol. 5, pp. 13-18 (2009).　

(38) M. Mochizuki, Computational Welding Mechanics from Mega- to Micro-Scopic Structures, Proceedings of the 20th PAM Users’ Conference in Asia ’09, Tokyo, Japan, No. VM23 (2009).　

(37) M. Mochizuki, Y. Mikami, S. Okano, S. Itoh and M. Shibahara, Fundamentals and Perspectives of Weld Distortion and Residual Stress, Textbook of Workshop on Welding Technology and Engineering (in Japanese), Shikoku Branch of Japan Welding Society, Tokushima, Japan, pp. 23-44 (2009).　

(36) M. Mochizuki, Welding Mechanics: Part I-1 - Fundamentals of Material Strength and Deformation, Textbook of 2009's Special Summer Lecture on Welding Engineering (in Japanese), Japan Welding Society, Osaka, Japan, pp. 39-56 (2009).

(35) M. Mochizuki, Characteristics and Perspectives of Welded Construction and Joints Using Ultra-Fine Grain Steel, Proceedings of International Seminar for NIMS Week 2009, Tsukuba, Japan, No. S-5-PL3 (2009).

(34) M. Mochizuki, Y. Mikami, Trend of Welding & Joining in Japan - Strength of Welded Joints, Journal of the Japan Welding Society (in Japanese), Vol. 78, No. 5, 450-452 (2009).

(33) K. Yasuda, H. Inoue, K. Wang, M. Mochizuki, K. Nishio, T. Koseki and Y. Sato, Trend of Welding & Joining in Japan - Welding Metallurgy of Steels, Journal of the Japan Welding Society (in Japanese), Vol. 78, No. 5, pp. 414-417 (2009).

(32) M. Mochizuki, Methodology Development for Adaptive Design and Fabrication in High Chromium Steel Welded Pipe-Joint for Sodium Cooled Fast Breeder Reactor, Proceedings of Annual Symposium for FY2008 on Innovative Nuclear Research and Development Program (in Japanese), Ministry of Education, Culture, Sports, Science and Technology of Japan, No. 070303 (2009).

(31) M. Mochizuki, Weld Distortion Simulation of Automotive Suspension Parts, Proceedings of the PAM Users' Conference in Asia '08, Tokyo, Japan, pp. 521-524 (2008).

(30) M. Mochizuki, Recent Trends of Welding Process Simulation, Research for Aging and Its Surrounding Technique in Nuclear Power Components - Report XV (in Japanese), Japan Welding Engineering Society JWES-AE-0808, pp. 53-76 (2008).

(29) K. Nishimoto, K. Saida, M. Mochizuki and H. Mori, Studies on High Reliability of Laser Welds in Stainless Steels, Proceedings of Nurturing Program Symposium for Nuclear Academics and Industries, (in Japanese), Ministry of Education, Culture, Sports, Science and Technology of Japan, Ministry of Economy, Trade and Industry of Japan, and Atomic Energy Society of Japan, Tokyo, Japan, pp. 59-60 (2008).

(28) S. Okano, M. Mochizuki and M. Toyoda, Proactive Countermeasure against Thermal Distortion during Weld Process, Proceedings of the PAM Users' Conference in Asia '07, Tokyo, Japan, pp. 273-280 (2007).

(27) M. Mochizuki, Trend of Welding & Joining in Japan - Strength of Welded Joints, Journal of the Japan Welding Society (in Japanese), Vol. 76, No. 5, pp. 382-383 (2007).

(26) M. Mochizuki, Importance of Weld Residual Stress and Recent Topics for Evaluation and Maintenance, Textbook of Welding, Residual Stress, and Strength in Nuclear Power Plants (in Japanese), Japan Welding Engineering Society, Tokyo, Japan, pp. 1-30 (2007).

(25) M. Mochizuki, Visual Study on Weld Distortion and Residual Stress, Invited Lecture of National Meeting Symposium of Japan Welding Society, Pre-Ptints of National Meeting of Japan Welding Society (in Japanese), Tokyo, Japan, Vol. 80, pp. S13-S20 (2007).

(24) M. Mochizuki, Standardization of Plant Diagnosis with Condition Based Monitoring, Textbook of 2nd Seminar on Advanced Maintenology and New Inspection System (in Japanese), Japan Society of Maintenology, pp. 149-169 (2006).

(23) M. Mochizuki and K. Miyazaki, How Can Residual Stress Analysis Results Apply to Integrity Assessment ?, Proceedings of the PAM Users' Conference in Asia '06, Tokyo, Japan, pp. 361-371 (2006).

(22) M. Mochizuki, Residual Stress and Maintenology, Part 2: Effect of Weld Residual Stress on Strength and Fracture, Journal of Japan Society of Maintenology (in Japanese), Vol. 5, No. 2, pp. 24-30 (2006).

(21) M. Mochizuki, Fundamentals of Welding Distortion and Residual Stress, Textbook of Special Summer Lecture on Welding Engineering - Proper Understanding of Weld Phenomena and Their Practical Application (in Japanese), Japan Welding Society, Osaka, Japan, pp. 35-62 (2006).

(20) M. Mochizuki, Residual Stress and Maintenology, Part 1: Fundamentals of Weld Distortion and Residual Stress, Journal of Japan Society of Maintenology (in Japanese), Vol. 5, No. 2, pp. 24-30 (2006).

(19) M. Mochizuki, Visualization of Weld Distortion and Residual Stress, Textbook of Technical School of Kansai Branch of Japan Welding Society (in Japanese), Trends of Visualization in Welding Process, Japan Welding Society, pp. 43-52 (2006).

(18) M. Mochizuki, How to Control Weld Distortion - Cuckoo Classification into Nobunaga, Hideyoshi, and Ieyasu, Welding Technology, Vol. 54, No. 1, pp. 76-87 (2006).

(17) M. Mochizuki, Generating Mechanism of Weld Distortion and Its Recent Evaluation Method, Textbook of 33rd Technical School of Eastern Branch of Japan Welding Society - Fabrication of Rail Stock and Trends of Thin Plate Welding (in Japanese), Japan Welding Society, pp. 46-64 (2005).

(16) M. Mochizuki and H. Shirai, Digital Engineering in Weld Fabrication Process, Proceedings of the PAM Users' Conference in Asia '05, Tokyo, Japan, pp. 481-490 (2005).

(15) M. Mochizuki, Trend of Welding & Joining in Japan - Strength of Welded Joints, Journal of the Japan Welding Society (in Japanese), Vol. 74, No. 5, pp. 321-322 (2005).

(14) M. Mochizuki, Fundamentals of Weld Distortion and Residual Stress, Textbook of Special Summer Lecture on Welding Engineering - Fundamentals and Applications for Assuring Weld Integrity (in Japanese), Japan Welding Society, pp. 43-61 (2005).

(13) M. Mochizuki, Weld Distortion Control and Fabrication Cost Reduction by Using Numerical Simulation, Proceedings of the PAM Users' Conference in Asia '04, Tokyo, Japan, pp. 441-457 (2004).

(12) S. Koga, M. Inuzuka, H. Nishida, M. Toyoda and M. Mochizuki, Characteristics of FEW Joints of Aluminum 5083 Thick Plates and Application to Large Structures, Textbook of Technical Seminar on Recent Trends of FSW Research and Development, Chugoku Branch of Japan Welding Society, Higashi-Hiroshima, Japan, pp. 31-45 (2004).

(11) M. Mochizuki, Welding Simulation of Steel Structures, Textbook of Workshop on Welding Simulation by Using Commercial Software (in Japanese), Chugoku Branch of Japan Welding Society, Higashi-Hiroshima, Japan, pp. 13-24 (2004).

(10) M. Mochizuki and M. Ohata, 2003 Review of Welding in Japan - Strength of Welded Joint and Fracture Toughness Evaluation, Journal of the Japan Welding Society (in Japanese), Vol. 73, No. 5, pp. 386-389 (2004).

(9) M. Mochizuki and M. Toyoda, Numerical Simulation of Temperature, Microstructure, and Stress-Strain Behaviors during Welding Process - Approach to Prediction Tool on Joint Performance in Welded Structures, Journal of the Japan Welding Society (in Japanese), Vol. 72, No. 8, pp. 631-639 (2003).

(8) M. Mochizuki, Arc Welding - Fundamentals of Arc Welding and Joint Performance, Textbook of Welding Seminar of Hokkaido Branch of Japan Welding Society (in Japanese), pp. 1-11 (2003).

(7) M. Mochizuki, Computation of Mechanical Properties in Materials Subjected to Welding Process, Proceedings of the PAM Users' Conference in Asia '03, Tokyo, Japan, pp. 469-496 (2003).

(6) M. Zako and M. Mochizuki, Trend Analysis of Members of Japan Welding Society in the Present and Future, Journal of the Japan Welding Society (in Japanese), Vol. 72, No. 5, pp. 445-454 (2003).

(5) M. Mochizuki, 2002 Review of Welding in Japan - Strength of Welded Joint and Fracture Toughness Evaluation (Static Strength and Buckling Strength), Journal of the Japan Welding Society (in Japanese), Vol. 72, No. 5, pp. 384-385 (2003).

(4) M. Mochizuki, A Methodology of Design and Fabrication for Welded Structures by Welding Process Simulation, Proceedings of the PAM Users' Conference in Asia '02, Yokohama, Japan, pp. 465-483 (2002).

(3) M. Mochizuki, 2001 Review of Welding in Japan - Strength of Welded Joint and Fracture Toughness Evaluation, Journal of the Japan Welding Society (in Japanese), Vol. 71, No. 5, pp. 357-359 (2002) (2002).

(2) M. Mochizuki, Approach to Manufacturing Science and Engineering for Welding Process Simulation, Proceedings of the PAM Users' Conference in Asia '01, Tokyo, Japan, pp. 395-406 (2001).

(1) M. Mochizuki, 1999 Review of Welding in Japan - Strength of Welded Joint and Fracture Toughness Evaluation, Journal of the Japan Welding Society (in Japanese), Vol. 69, No. 5, pp. 415-419 (2000).

4.2 Bulletin and Report in Universities and Institutes

(32) M. Mochizuki, M. Tanaka and S. Okano, Integrated Simulation Model between Arc Plasma Process and Weld Mechanics toward Accurate Distortion Analysis – Heat Source Modeling based on Welding Arc Physics, Transactions of the Japan Welding Research Institute of Osaka University, Vol. WSE2011, pp. 123-128 (2012).　

(31) H. Kitano, S. Okano and M. Mochizuki, Development of Evaluation Method for Residual Stress Distribution Fields Towards Higher Performance of Materials and Structures, Proceedings of the 5th Symposium and Annual Report of Global Center of Excellence for Advanced Structural and Functional Materials Design (in Japanese), (2012).

(30) N. Ochi, S. Okano and M. Mochizuki, Advancement of Weld Phenomena Simulation by Combining Arc Plasma, Molten Pool Configuration, and Thermal Deformation Models. Proceedings of the 5th Symposium and Annual Report of Global Center of Excellence for Advanced Structural and Functional Materials Design (in Japanese), (2012).

(29) M. Iyota, Y. Mikami and M. Mochizuki, Construction of Evaluation Method of Joint Performance in Resistance Spot Welding Considering Weld Characteristics, Proceedings of the 5th Symposium and Annual Report of Global Center of Excellence for Advanced Structural and Functional Materials Design (in Japanese), (2012).

(28) R. Ihara, M. Mochizuki and T. Hashimoto, Numerical Simulation of Residual Stress History during Piping Considering Recovery with Machined Thermal Cycles, Proceedings of the 5th Symposium and Annual Report of Global Center of Excellence for Advanced Structural and Functional Materials Design (in Japanese), (2012).

(27) M. Mochizuki, Y. Mikami and S. Okano, Studies Towards Construction of Structuring Design Methodology from Micro-Structural Design to Mega-Structure Fabrication by Using Coupling Design of Materials, Structures, and Fabrication, Proceedings of the 5th Symposium and Annual Report of Global Center of Excellence for Advanced Structural and Functional Materials Design (in Japanese), pp. 47-48 (2012).

(26) R. Ihara, T. Hashimoto and M. Mochizuki, Effects of Microstructuring by Machine Working on Microscopic Residual Stress and SCC Generation, Proceedings of the 4th Symposium and Annual Report of Global Center of Excellence for Advanced Structural and Functional Materials Design (in Japanese), pp. 85-86 (2011).　

(25) M. Mochizuki, Y. Mikami, S. Okano, S. Itoh and T. Hashimoto, Studies Towards Construction of Structuring Design Methodology from Micro-Structural Design to Mega-Structure Fabrication by Using Coupling Design of Materials, Structures, and Fabrication, Proceedings of the 4th Symposium and Annual Report of Global Center of Excellence for Advanced Structural and Functional Materials Design (in Japanese), pp. 47-48 (2011).　

(24) S. Nishikawa, S. Ohkita, K. Sogabe, Y. Mikami, M. Mochizuki and K. Ikeuchi, Effects of C and Nb Contents on Stress Corrosion Cracking of Shielded Metal Arc Weld Metal for 600 Type Alloy in High Temperature Pressurized Pure Water, Technical Review of NDE Center of Japan Power Engineering and Inspection Corporation, Vol. 6, pp. 31-39 (2010).

(23) M. Mochizuki, Y. Mikami, S. Okano, S. Itoh and T. Hashimoto, Studies Towards Construction of Structuring Design Methodology from Micro-Structural Design to Mega-Structure Fabrication by Using Coupling Design of Materials, Structures, and Fabrication, Proceedings of the 3rd Symposium and Annual Report of Global Center of Excellence for Advanced Structural and Functional Materials Design (in Japanese), pp. 47-48 (2010).　

(22) Y. Mikami, N. Kubota, Y. Iyota, H. Inoue, T. Kasuya, M. Mochizuki and K. Hiraoka, Numerical Simulation of Residual Stress in Weld Metal during Cold Crack Tests with Different Restraint Conditions, Proceedings of the 3rd Symposium of Global Collaborative Research Center for Computational Welding Science, Joining and Welding Research Institute of Osaka University, No. 3, pp. 3.1-3.8 (2009).　

(21) M. Mochizuki, Y. Mikami, S. Okano and S. Itoh, Studies Towards Construction of Structuring Design Methodology from Micro-Structural Design to Mega-Structure Fabrication by Using Coupling Design of Materials, Structures, and Fabrication, Proceedings of the 2nd Symposium and Annual Report of Global Center of Excellence for Advanced Structural and Functional Materials Design (in Japanese), pp. 47-48 (2009).

(20) Y. Mikami, M. Mochizuki, H. Murakawa and H. Serizawa, Numerical Simulation Method of Welding Distortion and Residual Stress Considering Characteristics of Phase Transformation, Proceedings of the Corporate Symposium in Joining and Welding Research Institute Symposium -JWRI Symposium 2008 (in Japanese), pp. 1-2 (2008).

(19) S. Okano, M. Mochizuki and M. Toyoda, Specification of Governing Factors of Weld Distortion Considering Temperature Field Characteristics and Its Application to Predicting and Controlling Weld Distortion, Proceedings of the 1st Symposium and Annual Report of Global Center of Excellence for Advanced Structural and Functional Materials Design (in Japanese), pp. 121-122 (2008).

(18) M. Mochizuki, Y. Mikami, S. Okano and M. Toyoda, Construction of Structuring Design Methodology from Micro-Structural Design to Mega-Structure Fabrication by Using Coupling Design of Materials, Structures, and Fabrication, Proceedings of the 1st Symposium and Annual Report of Global Center of Excellence for Advanced Structural and Functional Materials Design (in Japanese), pp. 79-82 (2008).

(17) R. Higuchi, M. Mochizuki and M. Toyoda, Evaluation of Stress Distribution Characteristics by FEM-MD Coupling Numerical Simulation Considering Microscopic Heterogeneity in Steels and Welds, Proceedings of the 5th Symposium and Annual Report of Center of Excellence for Advanced Structural and Functional Materials Design (in Japanese), pp. 145-146 (2007).

(16) S. Okano, M. Mochizuki and M. Toyoda, Development of Distortion Controlling Method by Temperature Field Control with Multiple Heat Sources, Proceedings of the 5th Symposium and Annual Report of Center of Excellence for Advanced Structural and Functional Materials Design (in Japanese), pp. 145-146 (2007).

(15) M. Toyoda and M. Mochizuki, Evolution of Coupling Design of Materials, Structures, and Fabrication Processes Toward Construction of Heterogeneous Mechanics, Proceedings of the 5th Symposium and Annual Report of Center of Excellence for Advanced Structural and Functional Materials Design (in Japanese), pp. 79-82 (2007).

(14) H. Shirai, M. Urushizaki, M. Mochizuki and M. Toyoda, Reduction of Welding Deformation by Split Laser Beams - Studies of Deformation Behavior by Laser Welding in Micron or Sub-Micron Area in Automobile Parts (Report 3), Denso Technical Review (in Japanese), Vol. 11, No. 2, pp. 87-93 (2006).

(13) Y. Mikami, M. Mochizuki and M. Toyoda, Development of Numerical Analysis of Welding Process Considering Phase Transformation and Its Application to Weld Distortion Control, Proceedings of the 4th Symposium and Annual Report of Center of Excellence for Advanced Structural and Functional Materials Design (in Japanese), pp. 103-104 (2006).

(12) R. Higuchi, M. Mochizuki and M. Toyoda, Analytical Study on Strength Characteristics of High-Tensile Strength Steel and Welds Considering Microscopic Heterogeneity, Proceedings of the 4th Symposium and Annual Report of Center of Excellence for Advanced Structural and Functional Materials Design (in Japanese), pp. 97-98 (2006).

(11) M. Toyoda and M. Mochizuki, Application to Coupling Design of Materials, Structures, and Fabrication Processes Toward Construction of Heterogeneous Mechanics, Proceedings of the 4th Symposium and Annual Report of Center of Excellence for Advanced Structural and Functional Materials Design (in Japanese), pp. 25-26 (2006).

(10) M. Mochizuki, Development of Coupling Simulation Model of Heat, Microstructure, and Mechanics during Thermal Processes in Structural Materials and Its Application to Welding, Research Reports on Kurata Grants, Kurata Memorial Hitachi Science and Technology Foundation, Vol. 35, pp. 44-46 (2005).

(9) M. Toyoda, M. Mochizuki, K. Hiraoka and T. Nakamura, Evaluation of Mis-Matching of Ultra-Narrow Gap Welded Structures for Structurization and Application of Ultra-Fine Grained Steel, Proceedings of the 2nd Cooperative Symposium of Center of Excellence for Advanced Structural and Functional Materials Design (in Japanese), pp. 13-14 (2005).

(8) Y. Mikami, M. Mochizuki and M. Toyoda, Development of Numerical Analysis of Welding Process Considering Phase Transformation and Its Application to Weld Distortion Control, Annual Report of Center of Excellence for Advanced Structural and Functional Materials Design (in Japanese), pp. 87-88 (2005).

(7) R. Higuchi, M. Mochizuki and M. Toyoda, Analytical Study on Strength Characteristics of High-Tensile Strength Steel and Welds Considering Microscopic Heterogeneity, Annual Report of Center of Excellence for Advanced Structural and Functional Materials Design (in Japanese), pp. 59-60 (2005).

(6) M. Toyoda, M. Mochizuki, K. Hiraoka and T. Nakamura, Prediction of Mis-Matching and Joint Performance of Ultra-Narrow Gap Welded Structures for Structurization and Application of Ultra-Fine Grained Steel, Annual Report of Center of Excellence for Advanced Structural and Functional Materials Design (in Japanese), pp. 49-50 (2005).

(5) M. Toyoda, M. Mochizuki and M. Ohata, Strength Evaluation Considering Multi-Scale Morphology in Structural Steels and Welded Joints for Constructing the Study Field of Strength and Mechanics in Heterogeneous Materials, Annual Report of Center of Excellence for Advanced Structural and Functional Materials Design (in Japanese), pp. 23-24 (2005).

(4) M. Toyoda and M. Mochizuki, Relationship between Macroscopic and Microscopic Morphology in Structural Steels and Welded Joints for Constructing the Study Field of Strength and Mechanics in Heterogeneous Materials, Annual Report of Center of Excellence for Advanced Structural and Functional Materials Design (in Japanese), pp. 39-42 (2004).

(3) M. Toyoda, M. Mochizuki and M. Ohata, Evaluation of Microscopic Heterogeneity in Structural Steels and Welded Joints for Constructing the Study Field of Strength and Mechanics in Heterogeneous Materials, Annual Report of Center of Excellence for Advanced Structural and Functional Materials Design (in Japanese), pp. 55-62 (2003).

(2) T. Shintomi, I. Chikushi, M. Ohata, M. Mochizuki and M. Toyoda, FE-Analysis of the Effect of Welding HAZ Softening on Tensile Strength, Nakayama Steel Technical Report, No. 39, pp. 42-48 (2002).

(1) Y. Ueda, M. G. Yuan, M. Mochizuki, S. Umezawa and K. Enomoto, A Predicting Method of Welding Residual Stress Using Source of Residual Stress (Report IV, Experimental Verification for Predicting Method of Welding Residual Stresses in T-Joints Using Inherent Strain), Transactions of the Japan Welding Research Institute of Osaka University, Vol. 22, No. 1, pp. 169-176 (1993).

4.3 Translation Papers

(21) R. Higuchi, M. Mochizuki and M. Toyoda, A Method for Evaluating the Stress-Strain Relationship of Materials in the Microstructural Region Using a Triangular Pyramidal Indenter, Welding International, Vol. 24, No. 8, pp. 611-619 (2010).　

(20) M. Mochizuki, Y. Mikami, H. Yamasaki and M. Toyoda, Analytical Study on Effects of Strain Distribution in Welding Start/End on Welding Distortion, Welding International, Vol. 23, No. 9, pp. 654-661 (2009).

(19) H. Mori, J. Katsuyama, M. Mochizuki, K. Nishimoto and M. Toyoda, Study on the Mechanism of Intergranular Stress Corrosion Cracking and Analysis of Residual Stress and Work Hardening in Welds of Low-carbon Austenitic Stainless Steel with Hard Surface Machining, Corrosion Engineering, Vol. 56, No. 12, pp. 757-770 (2007).

(18) S. Okano, M. Mochizuki and M. Toyoda, Thermal Conductivity Theoretical Examination Concerning Characteristics of Welding Distortion Produced by Multiple Heat Sources, Welding International, Vol. 21, No. 10, pp. 710-717 (2007).

(17) Y. Mikami, M. Mochizuki, M. Toyoda and Y. Morikage, Measurement and Numerical Simulation of Angular Distortion of Fillet Welded T-joints - Welding Angular Distortion Control by Transformation Expansion of Weld Metals (Report 1), Welding International, Vol. 21, No. 8, pp. 547-560 (2007).

(16) Y. Mikami, M. Mochizuki, M. Toyoda, Y. Hashiba, T. Hasegawa and S. Ohkita, Evaluation of Microstructural Phase Fractions and Hardness Distributions of Weld Metal Subjected to Multiple Thermal Cycle, Evaluation of Weld Hardness Distributions by Numerical Simulations of Welding Thermal Cycles and Microstructural Phase Fractions (2nd Report), Welding International, Vol. 20, No. 9, pp. 684-691 (2006).

(15) Y. Mikami, M. Mochizuki, M. Toyoda, T. Nakamura and K. Hiraoka, Numerical Simulations of Weld Hardness Distributions in Ultra-Narrow Gap GMA Welding, Evaluation of Weld Hardness Distributions by Numerical Simulations of Welding Thermal Cycles and Microstructural Phase Fractions (1st Report), Welding International, Vol. 20, No. 9, pp. 677-683 (2006).

(14) M. Mochizuki, S. Matsushima, M. Toyoda, Y. Morikage and T. Kubo, Study of Residual Stress Reduction in Welded Joints Using Phase Transformation Behavior of Welding Material, Studies on Numerical Simulation of Temperature, Microstructure, and Thermal Stress Histories during Welding and Their Application to Welded Structures (2nd Report), Welding International, Vol. 19, No. 10, pp. 773-782 (2005).

(13) H. Shirai, M. Urushizaki, M. Mochizuki and M. Toyoda, Reduction of Welding Deformation by the Twin Beams Method: A Study of Deformation Behavior due to Laser Welding of Automobile Parts at Micron or Submicron Level, Welding International, Vol. 19, No. 9, pp. 711-716 (2005).

(12) M. Mochizuki, S. Matsushima, M. Toyoda and C. Thaulow, Fundamental Study of Thermal Stress Generation during Welding Heat Cycles: Studies on Numerical Simulation of Temperature, Microstructure and Thermal Stress Histories during Welding, and Their Application to Welded Structures, Welding International, Vol. 19, No. 9, pp. 702-710 (2005).

(11) H. Shirai, M. Urushizaki, M. Mochizuki and M. Toyoda, The Effect of Beam Profile at a Focal Point on Welding Deformation: A Study of the Deformation Behavior by Laser Welding at Micron or Submicron Level in Automobile Parts, Welding International, Vol. 19, No. 9, pp. 681-686 (2005).

(10) H. Shirai, M. Urushizaki, S. Sawamoto, M. Mochizuki and M. Toyoda, Analysis of Bending Deformation Behavior during Circumferential Welding of Cylindrical Parts: Study of Deformation Behavior at Micron to Sub-Micron Level of Laser-Welded Automotive Parts, Welding International, Vol. 18, No. 8, pp. 626-634 (2004).

(9) M. Mochizuki and M. Toyoda, Effects of Welding Multiple Heat Cycles on Joint Performance in Beam-to-Column Welded Connection of Steel Framed Structures, Welding International, Vol. 18, No. 3, pp. 173-180 (2004).

(8) M. Mochizuki, Y. Mikami and M. Toyoda, Analytical Study on the Effects of Welding Deposition Sequence on Microstructure and Hardness in Beam-to-Column Welded Connection of Steel Framed Structures, Welding International, Vol. 18, No. 2, pp. 103-111 (2004).

(7) G. B. An, M. Ohata, M. Mochizuki, H. S. Bang and M. Toyoda, Analytical Examination of Ductile Crack Initiation with Strength Mismatch under Dynamic Loading - Criterion for Ductile Crack Initiation Effect of Strength Mismatch and Dynamic Loading, Journal of the Korean Welding Society (in Korean), Vol. 21, No. 7, pp. 755-764 (2003).

(6) G. B. An, M. Mochizuki, M. Ohata, H. S. Bang and M. Toyoda, Characteristics of Strength and Fracture in Strength Mismatched Joint by Dynamic Loading, Journal of the Korean Welding Society (in Korean), Vol. 21, No. 6, pp. 661-669 (2003).

(5) G. B. An, M. Mochizuki, M. Ohata, H. S. Bang and M. Toyoda, Thermal Elastic-Plastic Analysis of Strength Considering Temperature Rise due to Plastic Deformation by Dynamic Loading in Welded Joint, Journal of the Korean Welding Society (in Korean), Vol. 21, No. 3, pp. 324-333 (2003).

(4) M. Mochizuki, G. B. An, M. Toyoda and T. Ohmura, Strength and Fracture Properties of Undermatched Joints under Dynamic Loading - Study of Dynamic Deformation and Fracture Properties of Welded Joints with Strength Heterogeneity (Report 2), Welding International, Vol. 16, No. 5, pp. 376-384 (2002).

(3) M. Mochizuki, G. B. An, M. Toyoda and T. Ohmura, Thermal Elastic-Plastic Stress-Strain Analysis Considering Temperature Rise due to Plastic Deformation under Dynamic Loading in Undermatched Joints - Study of Dynamic Deformation and Fracture Properties of Welded Joints with Strength Heterogeneity (Report 1), Welding International, Vol. 16, No. 5, pp. 366-375 (2002).

(2) M. Mochizuki, K. Enomoto, N. Okamoto, H. Saito and E. Hayashi, Generation of Welding Residual Stress When a Pipe Penetrates a Thick Plate, Welding International, Vol. 9, No. 7, pp. 538-545 (1995).

(1) Y. Ueda, M. G. Yuan, M. Mochizuki, S. Umezawa and K. Enomoto, Experimental Verification of a Method for Prediction of Welding Residual Stresses in T Joints Using Inherent Strain, 4th Report: Method for Prediction Using Source of Residual Stress, Welding International, Vol. 7, No. 11, pp. 863-869 (1993).

4.4 Topics, etc.

(19) M. Mochizuki, Report of Maintenance Science Summer School 2011, Journal of Japan Society of Maintenology (in Japanese), Vol. 10, No. 3, pp. 88-91 (2011).　

(18) M. Mochizuki, Memories of Ai-Ko-Saka, Soh-Mon-Kai Alumni Bulletin of Aioi High School, No. 14, pp. 3 (2010).　

(17) M. Mochizuki, Preface - Scientific Approach to Preventive/Proactive Maintenance and Repair Techniques, E-Journal of Advanced Maintenance, Vol. 2, No. 2 (2010).　

(16) M. Mochizuki, T. Aoki, T. Ohgami, A. Sakashita and A. Yamaguchi, Report of 9th Maintenology Seminar on Condition Based Monitoring – With Examples of Different Industries, Journal of Japan Society of Maintenology (in Japanese), Vol. 9, No. 2, pp. 73-75 (2010).　

(15) T. Tagawa, T. Kubo, N. Konda, M. Mochizuki, M. Shibahara, K. Inose, Y. Mikami, Y. Kayamori, M. Yamamoto, Y. Yamashita, S. Kawaguchi, T. Kawabata, H. Hiramatsu, H. Serizawa, R. Kayano, S. Takaba, M. Kusaka, M. Satoh and K. Saida, Report of 2009 National Symposium on Welding Mechanics and Design, Journal of Japan Welding Society (in Japanese), Vol. 79, No. 3, pp. 534-537 (2010).　

(14) M. Mochizuki, Preface – On the 9th Maintenology Seminar on Condition Based Monitoring – With Examples of Different Industries, Textbook of Maintenology Seminar, Japan　 Society of Maintenology, Vol. 9, pp. 1 (2010).　

(13) K. Mitani and M. Mochizuki, Actual Stress and Thickness Measurement for Steel Pipes Using Electro-magnetic Acoustic Transducer, E-Journal of Advanced Maintenance, Vol. 1, No. 4, NT18 (2010).　

(12) A. Yamaguchi, M. Uesaka, M. Mochizuki, T. Yamashita and K. Hotta, Report of 7th Seminar on Advanced Condition Based Monitoring of Japan Society of Maintenology, Journal of Japan Society of Maintenology (in Japanese), Vol. 8, No. 2, pp. 60-63 (2009).

(11) M. Mochizuki, On the Sixty Years, Commemorative Book for 60th Anniversary of Commission of Ship-Building and Offshore Structures (in Japanese), Japan Welding Engineering Society, pp. 7 (2009).

(10) M. Mochizuki, Foreword for Special Issue on Trends of Condition Based Monitoring, Journal of Japanese Society for Non-Destructive Inspection (in Japanese), Vol. 58, No. 1, pp. 2 (2009).

(9) M. Mochizuki, Report of 1st Seminar on Aging and Maintenology of Japan Society of Maintenology, Journal of Japan Society of Maintenology (in Japanese), Vol. 4, No. 4, pp. 53-55 (2006).

(8) M. Mochizuki, Progress Report of Mini-Committee - Manufacturing Accuracy of Automotives, Journal of the Japan Welding Society (in Japanese), Vol. 74, No. 5, pp. 353 (2005).

(7) M. Mochizuki, Progress Report of Ad-Hoc Committee - Evaluation of Weld HAZ Undermatching and Tensile Strength Characteristics in High-Tensile Strength Steel Welded Joint, Journal of the Japan Welding Society (in Japanese), Vol. 73, No. 4, pp. 257-259 (2004).

(6) M. Mochizuki, Conference Report on the 7th International Seminar on Numerical Analysis of Weldability, Journal of the Japan Welding Society (in Japanese), Vol. 73, No. 1, pp. 56-58 (2004).

(5) M. Mochizuki, Pipe Dreamer Conference - Are you a pipe dreamer ?, The News of Engineering of Osaka University (in Japanese), Vol. 21, pp. 8 (2003).

(4) M. Mochizuki, Research Project on Weld Residual Stress in International Institute of Welding, Textbook of 6th Workshop on Thermal Process Simulation (in Japanese), Toyonaka, Japan, No. TPS-6-8 (2003).

(3) M. Mochizuki, Minutes of the IIW Sub-Commission X-F Meeting in Cambridge on Weld (Strength) Mis-Match Effect and Ductile Cracking, September 28th, 2001, TWI, Granta Park, Great Abington, Cambridge, United Kingdom, 55th Annual Assembly of the International Institute of Welding, Copenhagen, Denmark, IIW Doc. X-1495-2002 (2002).

(2) M. Mochizuki, Conference Review of the International Conference on the Application and Evaluation of High-Grade Linepipes in Hostile Environments, Pipes & Pipelines International, Vol. 47, No. 2, pp. 21-26 (2002).

(1) K. Arimochi, M. Ohata, Y. C. Kim, T. Kurashiki, N. Takano, K. Nakacho, N. Hasbe, F. Minami and M. Mochizuki, Report of 1999 National Symposium on Welding Mechanics and Design, Journal of Japan Welding Society (in Japanese), Vol. 69, No. 3 (2000).